Using physical disks from old RAID NAS
I had a WD MyCloud EX4100 NAS device with four 4TB SATA disks configured in a RAID 5 array (so, 16TB capacity, less overhead).
A lightning strike rendered the device inoperable. It will not boot.
The insurance company has replaced the NAS device with a new one. It is identical in every way (except perhaps firmware level), as the old device was only a year or so old.
I would like to replace the four blank disks in the new device with the four disks from the old one. I am assuming that the existing disks were not damaged by the lightning strike, only the NAS electronics.
Of course, I will respect the positioning of the physical drives in the array -- I'll put the drive from old slot 1 into new slot 1, etc.
If my assumption is correct that the physical drives were not damaged, should I be able to access my data on the new NAS device? Are there any settings I should make or other procedures I should follow before transferring the drives?
For bonus credit: To maximize the selling price, should I sell the four new, blank drives separately, or as a set of four?
hard-drive external-hard-drive raid sata nas
add a comment |
I had a WD MyCloud EX4100 NAS device with four 4TB SATA disks configured in a RAID 5 array (so, 16TB capacity, less overhead).
A lightning strike rendered the device inoperable. It will not boot.
The insurance company has replaced the NAS device with a new one. It is identical in every way (except perhaps firmware level), as the old device was only a year or so old.
I would like to replace the four blank disks in the new device with the four disks from the old one. I am assuming that the existing disks were not damaged by the lightning strike, only the NAS electronics.
Of course, I will respect the positioning of the physical drives in the array -- I'll put the drive from old slot 1 into new slot 1, etc.
If my assumption is correct that the physical drives were not damaged, should I be able to access my data on the new NAS device? Are there any settings I should make or other procedures I should follow before transferring the drives?
For bonus credit: To maximize the selling price, should I sell the four new, blank drives separately, or as a set of four?
hard-drive external-hard-drive raid sata nas
1
As far as I know RAID is depending on the Hardware and Firmware of the Controller. As you said the hardware is identical, only the firmware may have change. In this case i would say you could have luck an all will fit without problems. Regarding the drives: I think selling them separately will bring you more money, but I would keep at least one drive as spare.
– MarvinMcFly
Jan 31 at 18:56
Make an image of all the drives first, then put them back in the new enclosure in the same order and see if it recovers.
– Moab
Jan 31 at 20:02
add a comment |
I had a WD MyCloud EX4100 NAS device with four 4TB SATA disks configured in a RAID 5 array (so, 16TB capacity, less overhead).
A lightning strike rendered the device inoperable. It will not boot.
The insurance company has replaced the NAS device with a new one. It is identical in every way (except perhaps firmware level), as the old device was only a year or so old.
I would like to replace the four blank disks in the new device with the four disks from the old one. I am assuming that the existing disks were not damaged by the lightning strike, only the NAS electronics.
Of course, I will respect the positioning of the physical drives in the array -- I'll put the drive from old slot 1 into new slot 1, etc.
If my assumption is correct that the physical drives were not damaged, should I be able to access my data on the new NAS device? Are there any settings I should make or other procedures I should follow before transferring the drives?
For bonus credit: To maximize the selling price, should I sell the four new, blank drives separately, or as a set of four?
hard-drive external-hard-drive raid sata nas
I had a WD MyCloud EX4100 NAS device with four 4TB SATA disks configured in a RAID 5 array (so, 16TB capacity, less overhead).
A lightning strike rendered the device inoperable. It will not boot.
The insurance company has replaced the NAS device with a new one. It is identical in every way (except perhaps firmware level), as the old device was only a year or so old.
I would like to replace the four blank disks in the new device with the four disks from the old one. I am assuming that the existing disks were not damaged by the lightning strike, only the NAS electronics.
Of course, I will respect the positioning of the physical drives in the array -- I'll put the drive from old slot 1 into new slot 1, etc.
If my assumption is correct that the physical drives were not damaged, should I be able to access my data on the new NAS device? Are there any settings I should make or other procedures I should follow before transferring the drives?
For bonus credit: To maximize the selling price, should I sell the four new, blank drives separately, or as a set of four?
hard-drive external-hard-drive raid sata nas
hard-drive external-hard-drive raid sata nas
asked Jan 31 at 18:48
HemiPoweredDroneHemiPoweredDrone
1062
1062
1
As far as I know RAID is depending on the Hardware and Firmware of the Controller. As you said the hardware is identical, only the firmware may have change. In this case i would say you could have luck an all will fit without problems. Regarding the drives: I think selling them separately will bring you more money, but I would keep at least one drive as spare.
– MarvinMcFly
Jan 31 at 18:56
Make an image of all the drives first, then put them back in the new enclosure in the same order and see if it recovers.
– Moab
Jan 31 at 20:02
add a comment |
1
As far as I know RAID is depending on the Hardware and Firmware of the Controller. As you said the hardware is identical, only the firmware may have change. In this case i would say you could have luck an all will fit without problems. Regarding the drives: I think selling them separately will bring you more money, but I would keep at least one drive as spare.
– MarvinMcFly
Jan 31 at 18:56
Make an image of all the drives first, then put them back in the new enclosure in the same order and see if it recovers.
– Moab
Jan 31 at 20:02
1
1
As far as I know RAID is depending on the Hardware and Firmware of the Controller. As you said the hardware is identical, only the firmware may have change. In this case i would say you could have luck an all will fit without problems. Regarding the drives: I think selling them separately will bring you more money, but I would keep at least one drive as spare.
– MarvinMcFly
Jan 31 at 18:56
As far as I know RAID is depending on the Hardware and Firmware of the Controller. As you said the hardware is identical, only the firmware may have change. In this case i would say you could have luck an all will fit without problems. Regarding the drives: I think selling them separately will bring you more money, but I would keep at least one drive as spare.
– MarvinMcFly
Jan 31 at 18:56
Make an image of all the drives first, then put them back in the new enclosure in the same order and see if it recovers.
– Moab
Jan 31 at 20:02
Make an image of all the drives first, then put them back in the new enclosure in the same order and see if it recovers.
– Moab
Jan 31 at 20:02
add a comment |
1 Answer
1
active
oldest
votes
I figured this out. Migrating physical disks from one WD MyCloud 4100 enclosure to another is a supported process called RAID Roaming. The steps to follow are detailed here, in an official WD support article.
I followed the steps, and everything worked fine. All my old partitions and data are visible. I just had to update the firmware settings to match what I had before -- set the device name, set users and permissions, things like that.
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "3"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: true,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: 10,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f1400711%2fusing-physical-disks-from-old-raid-nas%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
I figured this out. Migrating physical disks from one WD MyCloud 4100 enclosure to another is a supported process called RAID Roaming. The steps to follow are detailed here, in an official WD support article.
I followed the steps, and everything worked fine. All my old partitions and data are visible. I just had to update the firmware settings to match what I had before -- set the device name, set users and permissions, things like that.
add a comment |
I figured this out. Migrating physical disks from one WD MyCloud 4100 enclosure to another is a supported process called RAID Roaming. The steps to follow are detailed here, in an official WD support article.
I followed the steps, and everything worked fine. All my old partitions and data are visible. I just had to update the firmware settings to match what I had before -- set the device name, set users and permissions, things like that.
add a comment |
I figured this out. Migrating physical disks from one WD MyCloud 4100 enclosure to another is a supported process called RAID Roaming. The steps to follow are detailed here, in an official WD support article.
I followed the steps, and everything worked fine. All my old partitions and data are visible. I just had to update the firmware settings to match what I had before -- set the device name, set users and permissions, things like that.
I figured this out. Migrating physical disks from one WD MyCloud 4100 enclosure to another is a supported process called RAID Roaming. The steps to follow are detailed here, in an official WD support article.
I followed the steps, and everything worked fine. All my old partitions and data are visible. I just had to update the firmware settings to match what I had before -- set the device name, set users and permissions, things like that.
answered Feb 2 at 2:54
HemiPoweredDroneHemiPoweredDrone
1062
1062
add a comment |
add a comment |
Thanks for contributing an answer to Super User!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f1400711%2fusing-physical-disks-from-old-raid-nas%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
1
As far as I know RAID is depending on the Hardware and Firmware of the Controller. As you said the hardware is identical, only the firmware may have change. In this case i would say you could have luck an all will fit without problems. Regarding the drives: I think selling them separately will bring you more money, but I would keep at least one drive as spare.
– MarvinMcFly
Jan 31 at 18:56
Make an image of all the drives first, then put them back in the new enclosure in the same order and see if it recovers.
– Moab
Jan 31 at 20:02