Does wire color matter in electronics?











up vote
29
down vote

favorite
5












I'm fairly new to electronics here. But I can't seem to find any clear answer anywhere on the internet.



Are wires special depending on their color? Or they have all the same purpose with just colors to define them so people won't get confused? Say I wanted to reverse the black and red wires on a LED strip connected to a battery, would it still function properly or not?



Just been curious about it lately..










share|improve this question


















  • 42




    When I was a kid, I got hold of a roll of wire with pink insulation - it was cheap, and I didn't have much money. I used pink wire for all connections because I saw no point in spending money on wire when I needed parts. Everything worked properly - despite the color. Finding mistakes in the wiring was no fun at all, though. "Does that pink wire go to +9V, or does this pink wire go to +9V?" Spent a lot of time tracing wires and measuring continuity. Made me really appreciate properly color coded wiring.
    – JRE
    Dec 3 at 16:44






  • 14




    Since we're swapping stories... When I was a kid... I built a 3 band radio. It was working sporadically, and I realized I needed the inductors and trimmer caps properly tuned with a signal generator. Didn't have one, so took the radio to a local shop (those shops existed back then). The guy took one look inside the box, looked at me pitifully, and then opened up a radio on sale and showed me. All wires color coded, neatly laid flat and tied to the chassis, completely visible end to end. One can still find that on high end stuff nowadays.
    – Indraneel
    Dec 3 at 16:56








  • 6




    The electricity flowing through a wire doesn't care about its color.
    – Mike Waters
    Dec 3 at 22:41






  • 22




    Building codes in some countries mandate that certain wire colors be used or not used. Wire harnesses in vehicles may use color codes consistently (or they may not). But generally, in electronics, it doesn't matter too much. But you SHOULD use black for ground, and if possible, avoid using black for that which is not ground. If you use black for VCC and red for ground, someone may eventually have cause to curse your name in the future.
    – mkeith
    Dec 4 at 1:49






  • 3




    One other point. Some wires are rated to be used outdoors and exposed to sunlight (UV). Black UV resistant wires probably hold up better to UV exposure than other colors. (A lot of people say this). But black wires that are NOT UV resistant won't hold up at all outside.
    – mkeith
    Dec 4 at 1:52















up vote
29
down vote

favorite
5












I'm fairly new to electronics here. But I can't seem to find any clear answer anywhere on the internet.



Are wires special depending on their color? Or they have all the same purpose with just colors to define them so people won't get confused? Say I wanted to reverse the black and red wires on a LED strip connected to a battery, would it still function properly or not?



Just been curious about it lately..










share|improve this question


















  • 42




    When I was a kid, I got hold of a roll of wire with pink insulation - it was cheap, and I didn't have much money. I used pink wire for all connections because I saw no point in spending money on wire when I needed parts. Everything worked properly - despite the color. Finding mistakes in the wiring was no fun at all, though. "Does that pink wire go to +9V, or does this pink wire go to +9V?" Spent a lot of time tracing wires and measuring continuity. Made me really appreciate properly color coded wiring.
    – JRE
    Dec 3 at 16:44






  • 14




    Since we're swapping stories... When I was a kid... I built a 3 band radio. It was working sporadically, and I realized I needed the inductors and trimmer caps properly tuned with a signal generator. Didn't have one, so took the radio to a local shop (those shops existed back then). The guy took one look inside the box, looked at me pitifully, and then opened up a radio on sale and showed me. All wires color coded, neatly laid flat and tied to the chassis, completely visible end to end. One can still find that on high end stuff nowadays.
    – Indraneel
    Dec 3 at 16:56








  • 6




    The electricity flowing through a wire doesn't care about its color.
    – Mike Waters
    Dec 3 at 22:41






  • 22




    Building codes in some countries mandate that certain wire colors be used or not used. Wire harnesses in vehicles may use color codes consistently (or they may not). But generally, in electronics, it doesn't matter too much. But you SHOULD use black for ground, and if possible, avoid using black for that which is not ground. If you use black for VCC and red for ground, someone may eventually have cause to curse your name in the future.
    – mkeith
    Dec 4 at 1:49






  • 3




    One other point. Some wires are rated to be used outdoors and exposed to sunlight (UV). Black UV resistant wires probably hold up better to UV exposure than other colors. (A lot of people say this). But black wires that are NOT UV resistant won't hold up at all outside.
    – mkeith
    Dec 4 at 1:52













up vote
29
down vote

favorite
5









up vote
29
down vote

favorite
5






5





I'm fairly new to electronics here. But I can't seem to find any clear answer anywhere on the internet.



Are wires special depending on their color? Or they have all the same purpose with just colors to define them so people won't get confused? Say I wanted to reverse the black and red wires on a LED strip connected to a battery, would it still function properly or not?



Just been curious about it lately..










share|improve this question













I'm fairly new to electronics here. But I can't seem to find any clear answer anywhere on the internet.



Are wires special depending on their color? Or they have all the same purpose with just colors to define them so people won't get confused? Say I wanted to reverse the black and red wires on a LED strip connected to a battery, would it still function properly or not?



Just been curious about it lately..







wire small-electronics






share|improve this question













share|improve this question











share|improve this question




share|improve this question










asked Dec 3 at 16:30









William Gregorio

168125




168125








  • 42




    When I was a kid, I got hold of a roll of wire with pink insulation - it was cheap, and I didn't have much money. I used pink wire for all connections because I saw no point in spending money on wire when I needed parts. Everything worked properly - despite the color. Finding mistakes in the wiring was no fun at all, though. "Does that pink wire go to +9V, or does this pink wire go to +9V?" Spent a lot of time tracing wires and measuring continuity. Made me really appreciate properly color coded wiring.
    – JRE
    Dec 3 at 16:44






  • 14




    Since we're swapping stories... When I was a kid... I built a 3 band radio. It was working sporadically, and I realized I needed the inductors and trimmer caps properly tuned with a signal generator. Didn't have one, so took the radio to a local shop (those shops existed back then). The guy took one look inside the box, looked at me pitifully, and then opened up a radio on sale and showed me. All wires color coded, neatly laid flat and tied to the chassis, completely visible end to end. One can still find that on high end stuff nowadays.
    – Indraneel
    Dec 3 at 16:56








  • 6




    The electricity flowing through a wire doesn't care about its color.
    – Mike Waters
    Dec 3 at 22:41






  • 22




    Building codes in some countries mandate that certain wire colors be used or not used. Wire harnesses in vehicles may use color codes consistently (or they may not). But generally, in electronics, it doesn't matter too much. But you SHOULD use black for ground, and if possible, avoid using black for that which is not ground. If you use black for VCC and red for ground, someone may eventually have cause to curse your name in the future.
    – mkeith
    Dec 4 at 1:49






  • 3




    One other point. Some wires are rated to be used outdoors and exposed to sunlight (UV). Black UV resistant wires probably hold up better to UV exposure than other colors. (A lot of people say this). But black wires that are NOT UV resistant won't hold up at all outside.
    – mkeith
    Dec 4 at 1:52














  • 42




    When I was a kid, I got hold of a roll of wire with pink insulation - it was cheap, and I didn't have much money. I used pink wire for all connections because I saw no point in spending money on wire when I needed parts. Everything worked properly - despite the color. Finding mistakes in the wiring was no fun at all, though. "Does that pink wire go to +9V, or does this pink wire go to +9V?" Spent a lot of time tracing wires and measuring continuity. Made me really appreciate properly color coded wiring.
    – JRE
    Dec 3 at 16:44






  • 14




    Since we're swapping stories... When I was a kid... I built a 3 band radio. It was working sporadically, and I realized I needed the inductors and trimmer caps properly tuned with a signal generator. Didn't have one, so took the radio to a local shop (those shops existed back then). The guy took one look inside the box, looked at me pitifully, and then opened up a radio on sale and showed me. All wires color coded, neatly laid flat and tied to the chassis, completely visible end to end. One can still find that on high end stuff nowadays.
    – Indraneel
    Dec 3 at 16:56








  • 6




    The electricity flowing through a wire doesn't care about its color.
    – Mike Waters
    Dec 3 at 22:41






  • 22




    Building codes in some countries mandate that certain wire colors be used or not used. Wire harnesses in vehicles may use color codes consistently (or they may not). But generally, in electronics, it doesn't matter too much. But you SHOULD use black for ground, and if possible, avoid using black for that which is not ground. If you use black for VCC and red for ground, someone may eventually have cause to curse your name in the future.
    – mkeith
    Dec 4 at 1:49






  • 3




    One other point. Some wires are rated to be used outdoors and exposed to sunlight (UV). Black UV resistant wires probably hold up better to UV exposure than other colors. (A lot of people say this). But black wires that are NOT UV resistant won't hold up at all outside.
    – mkeith
    Dec 4 at 1:52








42




42




When I was a kid, I got hold of a roll of wire with pink insulation - it was cheap, and I didn't have much money. I used pink wire for all connections because I saw no point in spending money on wire when I needed parts. Everything worked properly - despite the color. Finding mistakes in the wiring was no fun at all, though. "Does that pink wire go to +9V, or does this pink wire go to +9V?" Spent a lot of time tracing wires and measuring continuity. Made me really appreciate properly color coded wiring.
– JRE
Dec 3 at 16:44




When I was a kid, I got hold of a roll of wire with pink insulation - it was cheap, and I didn't have much money. I used pink wire for all connections because I saw no point in spending money on wire when I needed parts. Everything worked properly - despite the color. Finding mistakes in the wiring was no fun at all, though. "Does that pink wire go to +9V, or does this pink wire go to +9V?" Spent a lot of time tracing wires and measuring continuity. Made me really appreciate properly color coded wiring.
– JRE
Dec 3 at 16:44




14




14




Since we're swapping stories... When I was a kid... I built a 3 band radio. It was working sporadically, and I realized I needed the inductors and trimmer caps properly tuned with a signal generator. Didn't have one, so took the radio to a local shop (those shops existed back then). The guy took one look inside the box, looked at me pitifully, and then opened up a radio on sale and showed me. All wires color coded, neatly laid flat and tied to the chassis, completely visible end to end. One can still find that on high end stuff nowadays.
– Indraneel
Dec 3 at 16:56






Since we're swapping stories... When I was a kid... I built a 3 band radio. It was working sporadically, and I realized I needed the inductors and trimmer caps properly tuned with a signal generator. Didn't have one, so took the radio to a local shop (those shops existed back then). The guy took one look inside the box, looked at me pitifully, and then opened up a radio on sale and showed me. All wires color coded, neatly laid flat and tied to the chassis, completely visible end to end. One can still find that on high end stuff nowadays.
– Indraneel
Dec 3 at 16:56






6




6




The electricity flowing through a wire doesn't care about its color.
– Mike Waters
Dec 3 at 22:41




The electricity flowing through a wire doesn't care about its color.
– Mike Waters
Dec 3 at 22:41




22




22




Building codes in some countries mandate that certain wire colors be used or not used. Wire harnesses in vehicles may use color codes consistently (or they may not). But generally, in electronics, it doesn't matter too much. But you SHOULD use black for ground, and if possible, avoid using black for that which is not ground. If you use black for VCC and red for ground, someone may eventually have cause to curse your name in the future.
– mkeith
Dec 4 at 1:49




Building codes in some countries mandate that certain wire colors be used or not used. Wire harnesses in vehicles may use color codes consistently (or they may not). But generally, in electronics, it doesn't matter too much. But you SHOULD use black for ground, and if possible, avoid using black for that which is not ground. If you use black for VCC and red for ground, someone may eventually have cause to curse your name in the future.
– mkeith
Dec 4 at 1:49




3




3




One other point. Some wires are rated to be used outdoors and exposed to sunlight (UV). Black UV resistant wires probably hold up better to UV exposure than other colors. (A lot of people say this). But black wires that are NOT UV resistant won't hold up at all outside.
– mkeith
Dec 4 at 1:52




One other point. Some wires are rated to be used outdoors and exposed to sunlight (UV). Black UV resistant wires probably hold up better to UV exposure than other colors. (A lot of people say this). But black wires that are NOT UV resistant won't hold up at all outside.
– mkeith
Dec 4 at 1:52










9 Answers
9






active

oldest

votes

















up vote
69
down vote



accepted










The colors do not matter electrically. A wire is a wire is a wire, regardless of the color of their insulation. The color of the wire itself may matter when you get into higher voltages, but that's about the type of metal used (aluminum vs copper conductivity, for example).



The colors may matter, for readability, adhering to standards, legal compliance. But that normally doesn't apply to individual projects. You can use red for ground and black for power, just be aware that someone may see it and be confused. The led strip doesn't care about the color, but it will when someone thinks well, red is positive and black is ground so let me connect it the right way and something breaks when they connect it to the power source.






share|improve this answer

















  • 1




    @Baldrickk No, of course it doesn't physically matter. If all you have on hand is a lime-green wire, sure, drop it in, maybe make a note of it -- but there's still a use for standards, even in solo projects. If you have red and black wires, you should use those for power and ground, so you don't need to check back with your notes. If you don't, it doesn't change anything electrically, obviously -- it just makes it harder to get back into that project, even if you're the only one working on it.
    – Nic Hartley
    Dec 4 at 17:59












  • Comments are not for extended discussion (comments deleted)
    – W5VO
    Dec 4 at 18:32










  • Even more when "something" that breaks is you, because the wire had significant current and mis-colored wiring led you to believe something really hot was safe.
    – Joel Coehoorn
    Dec 5 at 2:44








  • 4




    @JoelCoehoorn well, electrically it is working properly. I guess getting killed wasn't exactly what you wanted to do, but the fact that you got killed means it works...
    – Nelson
    Dec 5 at 5:40








  • 1




    A wire is a wire is a wire, regardless of the color of their insulation. the same rule applies to human! Great answer!
    – ptr_user7813604
    Dec 8 at 16:48




















up vote
47
down vote













Wire colors are like comments in code, even for simple DIY projects. You're talking to your future self. When you take it apart in five years because it stops working, you will have forgotten everything about the original design, so it really helps to follow conventions. For industrial products it is vital to respect norms and conventions because many people may be involved in maintenance. This is also why we have silkscreen on boards, with testpoints labeled like "there should be 5V here".




Say I wanted to reverse the black and red wires on a LED strip connected to a battery, would it still function properly or not?




It will work fine until someone tries to troubleshoot it and says "Ha! There's your problem, the polarity is reversed!"



I've seen it happen. On another forum, a guy completely destroyed a very expensive synthesizer because the wiring colors did not match the polarity, and out of all the people trying to help him, none thought about the fact that the manufacturer had actually used a lot of power supplies which had been wired the wrong way.






share|improve this answer



















  • 17




    +1 Although as a programmer I have often said it the other way round, "Comments in code are like wire colors in hardware."
    – A. I. Breveleri
    Dec 4 at 4:13










  • Comments are not for extended discussion (comments deleted)
    – W5VO
    Dec 4 at 18:33






  • 2




    Before I saw this answer I was thinking that the different wire colours are like giving variables sensible names. If all your variables are named $v[0], $v[1] ... $v[n], (e.g. in PHP where any variable can be any type) you'll spend forever trying to fix bugs in it. If you can tell the purpose by paying attention to the colour/name, it will be much easier to understand.
    – CJ Dennis
    Dec 5 at 0:13


















up vote
17
down vote













Wire colour matters!



Not for the current running though the wire but for troubleshooting, safety, and others that may encounter any project. At powerline level voltages, national regulatory bodies have mandated the 'hot' line to be certain colours such as red for power (and orange, black, or brown in multi-phase power) and green or green/yellow striped as the grounded conductor.



In most low voltage DC systems I have encountered, red is positive and black is negative. It is so ingrained in our designs that people will assume it on a new system, and DIY products may only say 'connect red wire here'.



When you breadboard a new design, it will not matter electrically what colours you have chosen, but it is rare for me to have completed a moderately complex build without at least one error. To troubleshoot your design is so much easier if you are consistent with what colours you have used for what part of the circuit. Colour choices can be somewhat arbitrary, but for a DC system, keep red for positive, black for ground.



In other higher power systems, or RF, the wire colour or colour banding may be a manufacturing code that tells you what the internal makeup of the wire is. It could indicate insulation type (fire resistance, voltage rating) or conductor type (aluminum, copper, steel core) or other details. I worked in designing low voltage monitoring for high power systems. I was taught that red current only flows in red wires. Let me assure you that I have seen red current happily flowing in black wires until the molten copper explodes plating the room. I then kept the red current in the red wires.



Always assume that wire colours means something if you are working on an existing device, even if all it means is that this blue wire is a different circuit than that violet wire. I have been a broke student and wired electronic prototypes with the one roll of red hookup wire I had. They eventually worked but I paid in time troubleshooting. My professional work used national electrical code wire colours in large gauge but the low voltage signals used a different colour combination, but the wires were physically different which also helped separate them. And in production, each product was the exact same to simplify the repair department work.



So for your projects the positive and negative wires should have their own colour especially since this is where you often have to connect to external power, and then the signal(s) can have a third (or more) colour. If you have a small set of hookup wire spools, you can develop your own code particular to your projects; for example, blue for inputs, yellow for digital signals, violet for analog, and green for the output side. This will help you for years to come in troubleshooting. Remember that the colour is for your benefit and adjust your rules to your designs. If you keep the project, you can write the code down too.






share|improve this answer



















  • 1




    What is 'red current'? It's a confusing statement given that current flows from negative to positive.
    – CramerTV
    Dec 4 at 2:56






  • 5




    @CramerTV Given the tone of the answer, I think he said "red current" in a humorous way, refering to a current that, back then, should be only in red cables. It is not fair to downvote this answer for this. Just upwards there is a humorous comment about energy runing fast in red wire that received a lot of upvotes - it's a good thing that someone can smile on this.
    – mguima
    Dec 4 at 10:17










  • @CramerTV: it's even more confusing if you mix up words. Electrons flow from negative to positive voltage.
    – Guimoute
    Dec 7 at 10:14










  • @mguima, While humor is a great thing in ordinary life, when giving answers I think it is important to ensure the answers are clear and unambiguous - especially for newbies and for those who don't speak English natively. These sites show up in nearly every country around the world and making them as clear and concise as possible is something I believe is important, especially when dealing with potentially dangerous things like electricity. Also, I did not downvote so am unsure why any mention of that was made.
    – CramerTV
    Dec 7 at 16:58












  • @mguima there's a difference of it being in an answer vs a comment, a comment which was deleted for some reason.
    – Passerby
    Dec 8 at 17:47




















up vote
6
down vote













There are some color code conventions for low voltage (<24V) DC wiring:
Red is usually the positive supply line. Black is usually ground.
If there are multiple positive supplies, they will have other hot colors applied (brown, yellow, orange).
Pay attention that this is totally different from AC color codes. Do not mix these two under any circumstances.






share|improve this answer





















  • An explanation about why not to mix these two under any circumstances would be a great addition to the answer.
    – WoJ
    Dec 3 at 21:39






  • 2




    Do Not assume these colours apply to cars... on some English cars brown is live (not fused) and on German cars brown is earth or ground... :) hours of fun sorting out burnt wires after getting those mixed up...
    – Solar Mike
    Dec 3 at 22:27










  • Just an addition: in computer hardware, usually yellow is 12v, orange is 3.3v, and red is 5v. I've never seen an environment where those three voltages were present, and this pattern wasn't used.
    – mguima
    Dec 4 at 10:19








  • 3




    @WoJ Well I know of at least four different AC color codes (US, old German, old UK, European standard), and I suspect there are many more. They are all incompatible.
    – Martin Bonner
    Dec 4 at 13:04






  • 1




    @MartinBonner I believe USSR/China uses green as a phase colour.
    – Someone Somewhere
    Dec 5 at 7:52


















up vote
4
down vote













As noted, color does not matter, but it does make life easier when assembling and/or debugging.



Insulation type Does matter - for High Voltages (think tube amplifiers), direct underground, high temperature environments, durability. And then wire type depending on usage - single wires for breadboard, bundles of say 2 or 4 wires (speaker cord, lamp cord, or 4 for telephone line), twisted pair wire in othernet cable (4 pairs), shielded wire (microphone cable), bundles inside inside shielding (security system wire), twisted pair inside shielding with power & Gnd (USB cable?).



Then there's wire strands (single wire, not too flexible, or multiple strands, for more flexibility) and wire gage - 30 AWG single strand for wire-wrapping, 26 AWG solid for breadboard, #2 stranded (Car battery terminals) and all kinds of stuff in between.






share|improve this answer























  • I've normally used 22 solid for breadboarding purposes, seems to fit into .1" pin headers nicely - perhaps there are different size breadboards that use 26awg?
    – user2813274
    Dec 4 at 2:54






  • 1




    I could be off a size or two on the breadboard wiring, has been a while since I've done any. Too thick tho and it just mashes the spring contacts apart and ruins them.
    – CrossRoads
    Dec 4 at 5:04






  • 1




    In the late 1970s I worked as a "wireman", wiring equipment for a company supplying the UK military. You would mount boards, connectors, switches, controls, etc, in a steel cabinet and then wire it all together using wires of specified length, in a harness, all laced together using "lacing cord", and all these wires were the same colour. Pink.
    – Michael Harvey
    Dec 4 at 19:41




















up vote
4
down vote













Low voltage and "inside the box", color does not matter too much. There are two situations though where there are standards, one of them very important:



AC "Mains" Power



Colors for AC power do vary somewhat around the world. In the US, the general colors are:




  • White or Gray = Neutral

  • Green or bare = Ground

  • All other colors = Hot. For a number of reasons, the most common colors typically for hot (at least in residential applications) are Black followed by Red.


Anyone who works on 120V (and above) AC power should always treat any unknown wire as potentially hot, but when wiring is done properly, these standard colors help a lot to keep things straight and safe.



"Standard" Power Supplies



A classic example of de facto color coding is the ATX Power Supply. See the link for details, but it includes multiple wires of the same color for a given use including:




  • Orange = +3.3V

  • Black = Ground

  • Red = +5V

  • Yellow = +12V


Most people will never do more with an ATX power supply than swap one for another, and the connector only fits one way. But if you need to splice into one or are trying to build your own or do something else out of the ordinary with it, then sticking to the standard colors can make your life much easier.






share|improve this answer

















  • 3




    Just note that AC mains wire colours vary between countries. In the UK Blue is Neutral, Brown is Hot (as are Black and Grey in three phase). Old UK standard had Red as Hot and Black as Neutral. As ever, when in doubt refer to local standards.
    – Tom Carpenter
    Dec 3 at 22:45










  • Which is why I started off with Colors for AC power do vary somewhat around the world
    – manassehkatz
    Dec 3 at 23:17






  • 1




    missed that, my bad.
    – Tom Carpenter
    Dec 4 at 9:23






  • 2




    I think that the risk involved is inversely proportional to the reliability of the color codes. When dealing with AC, I think that is not advisable to consider that a wire is neutral only because it is white or gray (even if I did that installation myself - I confess that I would not swear that I've always observed the patterns). First thing to do is test / measure all the wires to discover if the color codes were used or not.
    – mguima
    Dec 4 at 10:03










  • Not to mention countries that have changed colour codes, such as the UK and much of Europe.
    – Someone Somewhere
    Dec 5 at 7:55


















up vote
4
down vote













Yes, the wire colors matter - just imagine when agent 007 opens up the box where there are 7 seconds left on the timer, wire cutters in hand, asks "which wire do I cut, they are all the same shade of grey?"



Unless you are a diabolical bomb maker & your intentions are to obfuscate your design, sticking to standard colors is highly reccomended for not just others, but even yourself to understand what you have done






share|improve this answer

















  • 6




    And if you are a diabolical bomb maker and you use all grey wires, sooner or later you will blow yourself up.
    – A. I. Breveleri
    Dec 4 at 4:15






  • 2




    Just never cut the red wire!
    – davidbak
    Dec 4 at 4:33






  • 1




    @A.I.Breveleri the chances of blowing yourself up as a diabolical bomb maker are high either way, but provided you use some other means of organisation (and properly test the circuits without live explosive attached), that risk doesn't go up that much more by the use of grey wires only.
    – leftaroundabout
    Dec 4 at 10:10






  • 1




    @davidbak it's considered good etiquette to put a big warning before any TVTropes link you post on StackExchange... like you also wouldn't pack a mail bomb without an “explosive hazard” sign, right? (Or with all-grey wiring...)
    – leftaroundabout
    Dec 4 at 10:16






  • 1




    @davidbak The Evil Overlord list provides plenty of advice. #15 seems applicable here. From cellblock A, #136 applies to OP's scenario. Warning: TV Tropes.
    – a CVn
    Dec 4 at 14:46




















up vote
4
down vote













Mark 'em yourself



enter image description here



This 5-pack of electrical tape is $4.



You don't have any particular obligation in homebrew electronics wiring (except to yourself, as confusing wires will waste a LOT of your time). The convention is red for positive and black for negative, particularly in a negative ground context.



However in mains wiring, you have some obligatory colors.




  • Equipment safety earthing must be green, green/yellow or bare.

  • If an active conductor is near earth voltage, it is called neutral, and it must be white or gray in North America or Philippines, and light blue in the rest of the world (black in Au/NZ).

  • "hot compared to earth" conductors are particular colors: much of the world brown then black then gray, North America any unreserved color (except orange for the high leg in 240V wild-leg) but convention is black then red then blue.






share|improve this answer





















  • Also, in North America, the three colors used for well pump wires are usually red, black and yellow.
    – mkeith
    Dec 8 at 2:51




















up vote
1
down vote













Color codes in wiring are regulated by ISO IEC 60445: 2017 "Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors".




IEC 60445:2017 applies to the identification and marking of terminals
of electrical equipment such as resistors, fuses, relays, contactors,
transformers, rotating machines and, wherever applicable, to
combinations of such equipment (e.g. assemblies), and also applies to
the identification of terminations of certain designated conductors.
It also provides general rules for the use of certain colours or
alphanumeric notations to identify conductors with the aim of avoiding
ambiguity and ensuring safe operation. These conductor colours or
alphanumeric notations are intended to be applied in cables or cores,
busbars, electrical equipment and installations. This basic safety
publication is primarily intended for use by technical committees in
the preparation of standards in accordance with the principles laid
down in IEC Guide 104 and ISO/IEC Guide 51. It has the status of a
basic safety publication in accordance with IEC Guide 104. This sixth
edition cancels and replaces the fifth edition of IEC 60445, published
in 2010.




In EU - and surely in Italy, were I live - standard norms issued by ISO, EN and UNI (Italian National Standards Organization) have force of law, and whoever wants to build anything must comply with all relevant and applicable standard norms.



In particular, compliancy with safety publications is strictly mandatory. Failure to comply will certainly lead to liability and prosecution in case of damages and/or injuries, not to mention death.



So, the answer is, "yes, wire colors matter in electronics"






share|improve this answer








New contributor




iw1dov is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.


















    Your Answer





    StackExchange.ifUsing("editor", function () {
    return StackExchange.using("mathjaxEditing", function () {
    StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
    StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
    });
    });
    }, "mathjax-editing");

    StackExchange.ifUsing("editor", function () {
    return StackExchange.using("schematics", function () {
    StackExchange.schematics.init();
    });
    }, "cicuitlab");

    StackExchange.ready(function() {
    var channelOptions = {
    tags: "".split(" "),
    id: "135"
    };
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function() {
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled) {
    StackExchange.using("snippets", function() {
    createEditor();
    });
    }
    else {
    createEditor();
    }
    });

    function createEditor() {
    StackExchange.prepareEditor({
    heartbeatType: 'answer',
    convertImagesToLinks: false,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: null,
    bindNavPrevention: true,
    postfix: "",
    imageUploader: {
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    },
    onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    });


    }
    });














    draft saved

    draft discarded


















    StackExchange.ready(
    function () {
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f410213%2fdoes-wire-color-matter-in-electronics%23new-answer', 'question_page');
    }
    );

    Post as a guest















    Required, but never shown

























    9 Answers
    9






    active

    oldest

    votes








    9 Answers
    9






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes








    up vote
    69
    down vote



    accepted










    The colors do not matter electrically. A wire is a wire is a wire, regardless of the color of their insulation. The color of the wire itself may matter when you get into higher voltages, but that's about the type of metal used (aluminum vs copper conductivity, for example).



    The colors may matter, for readability, adhering to standards, legal compliance. But that normally doesn't apply to individual projects. You can use red for ground and black for power, just be aware that someone may see it and be confused. The led strip doesn't care about the color, but it will when someone thinks well, red is positive and black is ground so let me connect it the right way and something breaks when they connect it to the power source.






    share|improve this answer

















    • 1




      @Baldrickk No, of course it doesn't physically matter. If all you have on hand is a lime-green wire, sure, drop it in, maybe make a note of it -- but there's still a use for standards, even in solo projects. If you have red and black wires, you should use those for power and ground, so you don't need to check back with your notes. If you don't, it doesn't change anything electrically, obviously -- it just makes it harder to get back into that project, even if you're the only one working on it.
      – Nic Hartley
      Dec 4 at 17:59












    • Comments are not for extended discussion (comments deleted)
      – W5VO
      Dec 4 at 18:32










    • Even more when "something" that breaks is you, because the wire had significant current and mis-colored wiring led you to believe something really hot was safe.
      – Joel Coehoorn
      Dec 5 at 2:44








    • 4




      @JoelCoehoorn well, electrically it is working properly. I guess getting killed wasn't exactly what you wanted to do, but the fact that you got killed means it works...
      – Nelson
      Dec 5 at 5:40








    • 1




      A wire is a wire is a wire, regardless of the color of their insulation. the same rule applies to human! Great answer!
      – ptr_user7813604
      Dec 8 at 16:48

















    up vote
    69
    down vote



    accepted










    The colors do not matter electrically. A wire is a wire is a wire, regardless of the color of their insulation. The color of the wire itself may matter when you get into higher voltages, but that's about the type of metal used (aluminum vs copper conductivity, for example).



    The colors may matter, for readability, adhering to standards, legal compliance. But that normally doesn't apply to individual projects. You can use red for ground and black for power, just be aware that someone may see it and be confused. The led strip doesn't care about the color, but it will when someone thinks well, red is positive and black is ground so let me connect it the right way and something breaks when they connect it to the power source.






    share|improve this answer

















    • 1




      @Baldrickk No, of course it doesn't physically matter. If all you have on hand is a lime-green wire, sure, drop it in, maybe make a note of it -- but there's still a use for standards, even in solo projects. If you have red and black wires, you should use those for power and ground, so you don't need to check back with your notes. If you don't, it doesn't change anything electrically, obviously -- it just makes it harder to get back into that project, even if you're the only one working on it.
      – Nic Hartley
      Dec 4 at 17:59












    • Comments are not for extended discussion (comments deleted)
      – W5VO
      Dec 4 at 18:32










    • Even more when "something" that breaks is you, because the wire had significant current and mis-colored wiring led you to believe something really hot was safe.
      – Joel Coehoorn
      Dec 5 at 2:44








    • 4




      @JoelCoehoorn well, electrically it is working properly. I guess getting killed wasn't exactly what you wanted to do, but the fact that you got killed means it works...
      – Nelson
      Dec 5 at 5:40








    • 1




      A wire is a wire is a wire, regardless of the color of their insulation. the same rule applies to human! Great answer!
      – ptr_user7813604
      Dec 8 at 16:48















    up vote
    69
    down vote



    accepted







    up vote
    69
    down vote



    accepted






    The colors do not matter electrically. A wire is a wire is a wire, regardless of the color of their insulation. The color of the wire itself may matter when you get into higher voltages, but that's about the type of metal used (aluminum vs copper conductivity, for example).



    The colors may matter, for readability, adhering to standards, legal compliance. But that normally doesn't apply to individual projects. You can use red for ground and black for power, just be aware that someone may see it and be confused. The led strip doesn't care about the color, but it will when someone thinks well, red is positive and black is ground so let me connect it the right way and something breaks when they connect it to the power source.






    share|improve this answer












    The colors do not matter electrically. A wire is a wire is a wire, regardless of the color of their insulation. The color of the wire itself may matter when you get into higher voltages, but that's about the type of metal used (aluminum vs copper conductivity, for example).



    The colors may matter, for readability, adhering to standards, legal compliance. But that normally doesn't apply to individual projects. You can use red for ground and black for power, just be aware that someone may see it and be confused. The led strip doesn't care about the color, but it will when someone thinks well, red is positive and black is ground so let me connect it the right way and something breaks when they connect it to the power source.







    share|improve this answer












    share|improve this answer



    share|improve this answer










    answered Dec 3 at 16:55









    Passerby

    56.6k451146




    56.6k451146








    • 1




      @Baldrickk No, of course it doesn't physically matter. If all you have on hand is a lime-green wire, sure, drop it in, maybe make a note of it -- but there's still a use for standards, even in solo projects. If you have red and black wires, you should use those for power and ground, so you don't need to check back with your notes. If you don't, it doesn't change anything electrically, obviously -- it just makes it harder to get back into that project, even if you're the only one working on it.
      – Nic Hartley
      Dec 4 at 17:59












    • Comments are not for extended discussion (comments deleted)
      – W5VO
      Dec 4 at 18:32










    • Even more when "something" that breaks is you, because the wire had significant current and mis-colored wiring led you to believe something really hot was safe.
      – Joel Coehoorn
      Dec 5 at 2:44








    • 4




      @JoelCoehoorn well, electrically it is working properly. I guess getting killed wasn't exactly what you wanted to do, but the fact that you got killed means it works...
      – Nelson
      Dec 5 at 5:40








    • 1




      A wire is a wire is a wire, regardless of the color of their insulation. the same rule applies to human! Great answer!
      – ptr_user7813604
      Dec 8 at 16:48
















    • 1




      @Baldrickk No, of course it doesn't physically matter. If all you have on hand is a lime-green wire, sure, drop it in, maybe make a note of it -- but there's still a use for standards, even in solo projects. If you have red and black wires, you should use those for power and ground, so you don't need to check back with your notes. If you don't, it doesn't change anything electrically, obviously -- it just makes it harder to get back into that project, even if you're the only one working on it.
      – Nic Hartley
      Dec 4 at 17:59












    • Comments are not for extended discussion (comments deleted)
      – W5VO
      Dec 4 at 18:32










    • Even more when "something" that breaks is you, because the wire had significant current and mis-colored wiring led you to believe something really hot was safe.
      – Joel Coehoorn
      Dec 5 at 2:44








    • 4




      @JoelCoehoorn well, electrically it is working properly. I guess getting killed wasn't exactly what you wanted to do, but the fact that you got killed means it works...
      – Nelson
      Dec 5 at 5:40








    • 1




      A wire is a wire is a wire, regardless of the color of their insulation. the same rule applies to human! Great answer!
      – ptr_user7813604
      Dec 8 at 16:48










    1




    1




    @Baldrickk No, of course it doesn't physically matter. If all you have on hand is a lime-green wire, sure, drop it in, maybe make a note of it -- but there's still a use for standards, even in solo projects. If you have red and black wires, you should use those for power and ground, so you don't need to check back with your notes. If you don't, it doesn't change anything electrically, obviously -- it just makes it harder to get back into that project, even if you're the only one working on it.
    – Nic Hartley
    Dec 4 at 17:59






    @Baldrickk No, of course it doesn't physically matter. If all you have on hand is a lime-green wire, sure, drop it in, maybe make a note of it -- but there's still a use for standards, even in solo projects. If you have red and black wires, you should use those for power and ground, so you don't need to check back with your notes. If you don't, it doesn't change anything electrically, obviously -- it just makes it harder to get back into that project, even if you're the only one working on it.
    – Nic Hartley
    Dec 4 at 17:59














    Comments are not for extended discussion (comments deleted)
    – W5VO
    Dec 4 at 18:32




    Comments are not for extended discussion (comments deleted)
    – W5VO
    Dec 4 at 18:32












    Even more when "something" that breaks is you, because the wire had significant current and mis-colored wiring led you to believe something really hot was safe.
    – Joel Coehoorn
    Dec 5 at 2:44






    Even more when "something" that breaks is you, because the wire had significant current and mis-colored wiring led you to believe something really hot was safe.
    – Joel Coehoorn
    Dec 5 at 2:44






    4




    4




    @JoelCoehoorn well, electrically it is working properly. I guess getting killed wasn't exactly what you wanted to do, but the fact that you got killed means it works...
    – Nelson
    Dec 5 at 5:40






    @JoelCoehoorn well, electrically it is working properly. I guess getting killed wasn't exactly what you wanted to do, but the fact that you got killed means it works...
    – Nelson
    Dec 5 at 5:40






    1




    1




    A wire is a wire is a wire, regardless of the color of their insulation. the same rule applies to human! Great answer!
    – ptr_user7813604
    Dec 8 at 16:48






    A wire is a wire is a wire, regardless of the color of their insulation. the same rule applies to human! Great answer!
    – ptr_user7813604
    Dec 8 at 16:48














    up vote
    47
    down vote













    Wire colors are like comments in code, even for simple DIY projects. You're talking to your future self. When you take it apart in five years because it stops working, you will have forgotten everything about the original design, so it really helps to follow conventions. For industrial products it is vital to respect norms and conventions because many people may be involved in maintenance. This is also why we have silkscreen on boards, with testpoints labeled like "there should be 5V here".




    Say I wanted to reverse the black and red wires on a LED strip connected to a battery, would it still function properly or not?




    It will work fine until someone tries to troubleshoot it and says "Ha! There's your problem, the polarity is reversed!"



    I've seen it happen. On another forum, a guy completely destroyed a very expensive synthesizer because the wiring colors did not match the polarity, and out of all the people trying to help him, none thought about the fact that the manufacturer had actually used a lot of power supplies which had been wired the wrong way.






    share|improve this answer



















    • 17




      +1 Although as a programmer I have often said it the other way round, "Comments in code are like wire colors in hardware."
      – A. I. Breveleri
      Dec 4 at 4:13










    • Comments are not for extended discussion (comments deleted)
      – W5VO
      Dec 4 at 18:33






    • 2




      Before I saw this answer I was thinking that the different wire colours are like giving variables sensible names. If all your variables are named $v[0], $v[1] ... $v[n], (e.g. in PHP where any variable can be any type) you'll spend forever trying to fix bugs in it. If you can tell the purpose by paying attention to the colour/name, it will be much easier to understand.
      – CJ Dennis
      Dec 5 at 0:13















    up vote
    47
    down vote













    Wire colors are like comments in code, even for simple DIY projects. You're talking to your future self. When you take it apart in five years because it stops working, you will have forgotten everything about the original design, so it really helps to follow conventions. For industrial products it is vital to respect norms and conventions because many people may be involved in maintenance. This is also why we have silkscreen on boards, with testpoints labeled like "there should be 5V here".




    Say I wanted to reverse the black and red wires on a LED strip connected to a battery, would it still function properly or not?




    It will work fine until someone tries to troubleshoot it and says "Ha! There's your problem, the polarity is reversed!"



    I've seen it happen. On another forum, a guy completely destroyed a very expensive synthesizer because the wiring colors did not match the polarity, and out of all the people trying to help him, none thought about the fact that the manufacturer had actually used a lot of power supplies which had been wired the wrong way.






    share|improve this answer



















    • 17




      +1 Although as a programmer I have often said it the other way round, "Comments in code are like wire colors in hardware."
      – A. I. Breveleri
      Dec 4 at 4:13










    • Comments are not for extended discussion (comments deleted)
      – W5VO
      Dec 4 at 18:33






    • 2




      Before I saw this answer I was thinking that the different wire colours are like giving variables sensible names. If all your variables are named $v[0], $v[1] ... $v[n], (e.g. in PHP where any variable can be any type) you'll spend forever trying to fix bugs in it. If you can tell the purpose by paying attention to the colour/name, it will be much easier to understand.
      – CJ Dennis
      Dec 5 at 0:13













    up vote
    47
    down vote










    up vote
    47
    down vote









    Wire colors are like comments in code, even for simple DIY projects. You're talking to your future self. When you take it apart in five years because it stops working, you will have forgotten everything about the original design, so it really helps to follow conventions. For industrial products it is vital to respect norms and conventions because many people may be involved in maintenance. This is also why we have silkscreen on boards, with testpoints labeled like "there should be 5V here".




    Say I wanted to reverse the black and red wires on a LED strip connected to a battery, would it still function properly or not?




    It will work fine until someone tries to troubleshoot it and says "Ha! There's your problem, the polarity is reversed!"



    I've seen it happen. On another forum, a guy completely destroyed a very expensive synthesizer because the wiring colors did not match the polarity, and out of all the people trying to help him, none thought about the fact that the manufacturer had actually used a lot of power supplies which had been wired the wrong way.






    share|improve this answer














    Wire colors are like comments in code, even for simple DIY projects. You're talking to your future self. When you take it apart in five years because it stops working, you will have forgotten everything about the original design, so it really helps to follow conventions. For industrial products it is vital to respect norms and conventions because many people may be involved in maintenance. This is also why we have silkscreen on boards, with testpoints labeled like "there should be 5V here".




    Say I wanted to reverse the black and red wires on a LED strip connected to a battery, would it still function properly or not?




    It will work fine until someone tries to troubleshoot it and says "Ha! There's your problem, the polarity is reversed!"



    I've seen it happen. On another forum, a guy completely destroyed a very expensive synthesizer because the wiring colors did not match the polarity, and out of all the people trying to help him, none thought about the fact that the manufacturer had actually used a lot of power supplies which had been wired the wrong way.







    share|improve this answer














    share|improve this answer



    share|improve this answer








    edited Dec 3 at 22:47

























    answered Dec 3 at 22:41









    peufeu

    23.9k23971




    23.9k23971








    • 17




      +1 Although as a programmer I have often said it the other way round, "Comments in code are like wire colors in hardware."
      – A. I. Breveleri
      Dec 4 at 4:13










    • Comments are not for extended discussion (comments deleted)
      – W5VO
      Dec 4 at 18:33






    • 2




      Before I saw this answer I was thinking that the different wire colours are like giving variables sensible names. If all your variables are named $v[0], $v[1] ... $v[n], (e.g. in PHP where any variable can be any type) you'll spend forever trying to fix bugs in it. If you can tell the purpose by paying attention to the colour/name, it will be much easier to understand.
      – CJ Dennis
      Dec 5 at 0:13














    • 17




      +1 Although as a programmer I have often said it the other way round, "Comments in code are like wire colors in hardware."
      – A. I. Breveleri
      Dec 4 at 4:13










    • Comments are not for extended discussion (comments deleted)
      – W5VO
      Dec 4 at 18:33






    • 2




      Before I saw this answer I was thinking that the different wire colours are like giving variables sensible names. If all your variables are named $v[0], $v[1] ... $v[n], (e.g. in PHP where any variable can be any type) you'll spend forever trying to fix bugs in it. If you can tell the purpose by paying attention to the colour/name, it will be much easier to understand.
      – CJ Dennis
      Dec 5 at 0:13








    17




    17




    +1 Although as a programmer I have often said it the other way round, "Comments in code are like wire colors in hardware."
    – A. I. Breveleri
    Dec 4 at 4:13




    +1 Although as a programmer I have often said it the other way round, "Comments in code are like wire colors in hardware."
    – A. I. Breveleri
    Dec 4 at 4:13












    Comments are not for extended discussion (comments deleted)
    – W5VO
    Dec 4 at 18:33




    Comments are not for extended discussion (comments deleted)
    – W5VO
    Dec 4 at 18:33




    2




    2




    Before I saw this answer I was thinking that the different wire colours are like giving variables sensible names. If all your variables are named $v[0], $v[1] ... $v[n], (e.g. in PHP where any variable can be any type) you'll spend forever trying to fix bugs in it. If you can tell the purpose by paying attention to the colour/name, it will be much easier to understand.
    – CJ Dennis
    Dec 5 at 0:13




    Before I saw this answer I was thinking that the different wire colours are like giving variables sensible names. If all your variables are named $v[0], $v[1] ... $v[n], (e.g. in PHP where any variable can be any type) you'll spend forever trying to fix bugs in it. If you can tell the purpose by paying attention to the colour/name, it will be much easier to understand.
    – CJ Dennis
    Dec 5 at 0:13










    up vote
    17
    down vote













    Wire colour matters!



    Not for the current running though the wire but for troubleshooting, safety, and others that may encounter any project. At powerline level voltages, national regulatory bodies have mandated the 'hot' line to be certain colours such as red for power (and orange, black, or brown in multi-phase power) and green or green/yellow striped as the grounded conductor.



    In most low voltage DC systems I have encountered, red is positive and black is negative. It is so ingrained in our designs that people will assume it on a new system, and DIY products may only say 'connect red wire here'.



    When you breadboard a new design, it will not matter electrically what colours you have chosen, but it is rare for me to have completed a moderately complex build without at least one error. To troubleshoot your design is so much easier if you are consistent with what colours you have used for what part of the circuit. Colour choices can be somewhat arbitrary, but for a DC system, keep red for positive, black for ground.



    In other higher power systems, or RF, the wire colour or colour banding may be a manufacturing code that tells you what the internal makeup of the wire is. It could indicate insulation type (fire resistance, voltage rating) or conductor type (aluminum, copper, steel core) or other details. I worked in designing low voltage monitoring for high power systems. I was taught that red current only flows in red wires. Let me assure you that I have seen red current happily flowing in black wires until the molten copper explodes plating the room. I then kept the red current in the red wires.



    Always assume that wire colours means something if you are working on an existing device, even if all it means is that this blue wire is a different circuit than that violet wire. I have been a broke student and wired electronic prototypes with the one roll of red hookup wire I had. They eventually worked but I paid in time troubleshooting. My professional work used national electrical code wire colours in large gauge but the low voltage signals used a different colour combination, but the wires were physically different which also helped separate them. And in production, each product was the exact same to simplify the repair department work.



    So for your projects the positive and negative wires should have their own colour especially since this is where you often have to connect to external power, and then the signal(s) can have a third (or more) colour. If you have a small set of hookup wire spools, you can develop your own code particular to your projects; for example, blue for inputs, yellow for digital signals, violet for analog, and green for the output side. This will help you for years to come in troubleshooting. Remember that the colour is for your benefit and adjust your rules to your designs. If you keep the project, you can write the code down too.






    share|improve this answer



















    • 1




      What is 'red current'? It's a confusing statement given that current flows from negative to positive.
      – CramerTV
      Dec 4 at 2:56






    • 5




      @CramerTV Given the tone of the answer, I think he said "red current" in a humorous way, refering to a current that, back then, should be only in red cables. It is not fair to downvote this answer for this. Just upwards there is a humorous comment about energy runing fast in red wire that received a lot of upvotes - it's a good thing that someone can smile on this.
      – mguima
      Dec 4 at 10:17










    • @CramerTV: it's even more confusing if you mix up words. Electrons flow from negative to positive voltage.
      – Guimoute
      Dec 7 at 10:14










    • @mguima, While humor is a great thing in ordinary life, when giving answers I think it is important to ensure the answers are clear and unambiguous - especially for newbies and for those who don't speak English natively. These sites show up in nearly every country around the world and making them as clear and concise as possible is something I believe is important, especially when dealing with potentially dangerous things like electricity. Also, I did not downvote so am unsure why any mention of that was made.
      – CramerTV
      Dec 7 at 16:58












    • @mguima there's a difference of it being in an answer vs a comment, a comment which was deleted for some reason.
      – Passerby
      Dec 8 at 17:47

















    up vote
    17
    down vote













    Wire colour matters!



    Not for the current running though the wire but for troubleshooting, safety, and others that may encounter any project. At powerline level voltages, national regulatory bodies have mandated the 'hot' line to be certain colours such as red for power (and orange, black, or brown in multi-phase power) and green or green/yellow striped as the grounded conductor.



    In most low voltage DC systems I have encountered, red is positive and black is negative. It is so ingrained in our designs that people will assume it on a new system, and DIY products may only say 'connect red wire here'.



    When you breadboard a new design, it will not matter electrically what colours you have chosen, but it is rare for me to have completed a moderately complex build without at least one error. To troubleshoot your design is so much easier if you are consistent with what colours you have used for what part of the circuit. Colour choices can be somewhat arbitrary, but for a DC system, keep red for positive, black for ground.



    In other higher power systems, or RF, the wire colour or colour banding may be a manufacturing code that tells you what the internal makeup of the wire is. It could indicate insulation type (fire resistance, voltage rating) or conductor type (aluminum, copper, steel core) or other details. I worked in designing low voltage monitoring for high power systems. I was taught that red current only flows in red wires. Let me assure you that I have seen red current happily flowing in black wires until the molten copper explodes plating the room. I then kept the red current in the red wires.



    Always assume that wire colours means something if you are working on an existing device, even if all it means is that this blue wire is a different circuit than that violet wire. I have been a broke student and wired electronic prototypes with the one roll of red hookup wire I had. They eventually worked but I paid in time troubleshooting. My professional work used national electrical code wire colours in large gauge but the low voltage signals used a different colour combination, but the wires were physically different which also helped separate them. And in production, each product was the exact same to simplify the repair department work.



    So for your projects the positive and negative wires should have their own colour especially since this is where you often have to connect to external power, and then the signal(s) can have a third (or more) colour. If you have a small set of hookup wire spools, you can develop your own code particular to your projects; for example, blue for inputs, yellow for digital signals, violet for analog, and green for the output side. This will help you for years to come in troubleshooting. Remember that the colour is for your benefit and adjust your rules to your designs. If you keep the project, you can write the code down too.






    share|improve this answer



















    • 1




      What is 'red current'? It's a confusing statement given that current flows from negative to positive.
      – CramerTV
      Dec 4 at 2:56






    • 5




      @CramerTV Given the tone of the answer, I think he said "red current" in a humorous way, refering to a current that, back then, should be only in red cables. It is not fair to downvote this answer for this. Just upwards there is a humorous comment about energy runing fast in red wire that received a lot of upvotes - it's a good thing that someone can smile on this.
      – mguima
      Dec 4 at 10:17










    • @CramerTV: it's even more confusing if you mix up words. Electrons flow from negative to positive voltage.
      – Guimoute
      Dec 7 at 10:14










    • @mguima, While humor is a great thing in ordinary life, when giving answers I think it is important to ensure the answers are clear and unambiguous - especially for newbies and for those who don't speak English natively. These sites show up in nearly every country around the world and making them as clear and concise as possible is something I believe is important, especially when dealing with potentially dangerous things like electricity. Also, I did not downvote so am unsure why any mention of that was made.
      – CramerTV
      Dec 7 at 16:58












    • @mguima there's a difference of it being in an answer vs a comment, a comment which was deleted for some reason.
      – Passerby
      Dec 8 at 17:47















    up vote
    17
    down vote










    up vote
    17
    down vote









    Wire colour matters!



    Not for the current running though the wire but for troubleshooting, safety, and others that may encounter any project. At powerline level voltages, national regulatory bodies have mandated the 'hot' line to be certain colours such as red for power (and orange, black, or brown in multi-phase power) and green or green/yellow striped as the grounded conductor.



    In most low voltage DC systems I have encountered, red is positive and black is negative. It is so ingrained in our designs that people will assume it on a new system, and DIY products may only say 'connect red wire here'.



    When you breadboard a new design, it will not matter electrically what colours you have chosen, but it is rare for me to have completed a moderately complex build without at least one error. To troubleshoot your design is so much easier if you are consistent with what colours you have used for what part of the circuit. Colour choices can be somewhat arbitrary, but for a DC system, keep red for positive, black for ground.



    In other higher power systems, or RF, the wire colour or colour banding may be a manufacturing code that tells you what the internal makeup of the wire is. It could indicate insulation type (fire resistance, voltage rating) or conductor type (aluminum, copper, steel core) or other details. I worked in designing low voltage monitoring for high power systems. I was taught that red current only flows in red wires. Let me assure you that I have seen red current happily flowing in black wires until the molten copper explodes plating the room. I then kept the red current in the red wires.



    Always assume that wire colours means something if you are working on an existing device, even if all it means is that this blue wire is a different circuit than that violet wire. I have been a broke student and wired electronic prototypes with the one roll of red hookup wire I had. They eventually worked but I paid in time troubleshooting. My professional work used national electrical code wire colours in large gauge but the low voltage signals used a different colour combination, but the wires were physically different which also helped separate them. And in production, each product was the exact same to simplify the repair department work.



    So for your projects the positive and negative wires should have their own colour especially since this is where you often have to connect to external power, and then the signal(s) can have a third (or more) colour. If you have a small set of hookup wire spools, you can develop your own code particular to your projects; for example, blue for inputs, yellow for digital signals, violet for analog, and green for the output side. This will help you for years to come in troubleshooting. Remember that the colour is for your benefit and adjust your rules to your designs. If you keep the project, you can write the code down too.






    share|improve this answer














    Wire colour matters!



    Not for the current running though the wire but for troubleshooting, safety, and others that may encounter any project. At powerline level voltages, national regulatory bodies have mandated the 'hot' line to be certain colours such as red for power (and orange, black, or brown in multi-phase power) and green or green/yellow striped as the grounded conductor.



    In most low voltage DC systems I have encountered, red is positive and black is negative. It is so ingrained in our designs that people will assume it on a new system, and DIY products may only say 'connect red wire here'.



    When you breadboard a new design, it will not matter electrically what colours you have chosen, but it is rare for me to have completed a moderately complex build without at least one error. To troubleshoot your design is so much easier if you are consistent with what colours you have used for what part of the circuit. Colour choices can be somewhat arbitrary, but for a DC system, keep red for positive, black for ground.



    In other higher power systems, or RF, the wire colour or colour banding may be a manufacturing code that tells you what the internal makeup of the wire is. It could indicate insulation type (fire resistance, voltage rating) or conductor type (aluminum, copper, steel core) or other details. I worked in designing low voltage monitoring for high power systems. I was taught that red current only flows in red wires. Let me assure you that I have seen red current happily flowing in black wires until the molten copper explodes plating the room. I then kept the red current in the red wires.



    Always assume that wire colours means something if you are working on an existing device, even if all it means is that this blue wire is a different circuit than that violet wire. I have been a broke student and wired electronic prototypes with the one roll of red hookup wire I had. They eventually worked but I paid in time troubleshooting. My professional work used national electrical code wire colours in large gauge but the low voltage signals used a different colour combination, but the wires were physically different which also helped separate them. And in production, each product was the exact same to simplify the repair department work.



    So for your projects the positive and negative wires should have their own colour especially since this is where you often have to connect to external power, and then the signal(s) can have a third (or more) colour. If you have a small set of hookup wire spools, you can develop your own code particular to your projects; for example, blue for inputs, yellow for digital signals, violet for analog, and green for the output side. This will help you for years to come in troubleshooting. Remember that the colour is for your benefit and adjust your rules to your designs. If you keep the project, you can write the code down too.







    share|improve this answer














    share|improve this answer



    share|improve this answer








    edited Dec 7 at 11:27









    david

    1033




    1033










    answered Dec 3 at 22:09









    James

    1792




    1792








    • 1




      What is 'red current'? It's a confusing statement given that current flows from negative to positive.
      – CramerTV
      Dec 4 at 2:56






    • 5




      @CramerTV Given the tone of the answer, I think he said "red current" in a humorous way, refering to a current that, back then, should be only in red cables. It is not fair to downvote this answer for this. Just upwards there is a humorous comment about energy runing fast in red wire that received a lot of upvotes - it's a good thing that someone can smile on this.
      – mguima
      Dec 4 at 10:17










    • @CramerTV: it's even more confusing if you mix up words. Electrons flow from negative to positive voltage.
      – Guimoute
      Dec 7 at 10:14










    • @mguima, While humor is a great thing in ordinary life, when giving answers I think it is important to ensure the answers are clear and unambiguous - especially for newbies and for those who don't speak English natively. These sites show up in nearly every country around the world and making them as clear and concise as possible is something I believe is important, especially when dealing with potentially dangerous things like electricity. Also, I did not downvote so am unsure why any mention of that was made.
      – CramerTV
      Dec 7 at 16:58












    • @mguima there's a difference of it being in an answer vs a comment, a comment which was deleted for some reason.
      – Passerby
      Dec 8 at 17:47
















    • 1




      What is 'red current'? It's a confusing statement given that current flows from negative to positive.
      – CramerTV
      Dec 4 at 2:56






    • 5




      @CramerTV Given the tone of the answer, I think he said "red current" in a humorous way, refering to a current that, back then, should be only in red cables. It is not fair to downvote this answer for this. Just upwards there is a humorous comment about energy runing fast in red wire that received a lot of upvotes - it's a good thing that someone can smile on this.
      – mguima
      Dec 4 at 10:17










    • @CramerTV: it's even more confusing if you mix up words. Electrons flow from negative to positive voltage.
      – Guimoute
      Dec 7 at 10:14










    • @mguima, While humor is a great thing in ordinary life, when giving answers I think it is important to ensure the answers are clear and unambiguous - especially for newbies and for those who don't speak English natively. These sites show up in nearly every country around the world and making them as clear and concise as possible is something I believe is important, especially when dealing with potentially dangerous things like electricity. Also, I did not downvote so am unsure why any mention of that was made.
      – CramerTV
      Dec 7 at 16:58












    • @mguima there's a difference of it being in an answer vs a comment, a comment which was deleted for some reason.
      – Passerby
      Dec 8 at 17:47










    1




    1




    What is 'red current'? It's a confusing statement given that current flows from negative to positive.
    – CramerTV
    Dec 4 at 2:56




    What is 'red current'? It's a confusing statement given that current flows from negative to positive.
    – CramerTV
    Dec 4 at 2:56




    5




    5




    @CramerTV Given the tone of the answer, I think he said "red current" in a humorous way, refering to a current that, back then, should be only in red cables. It is not fair to downvote this answer for this. Just upwards there is a humorous comment about energy runing fast in red wire that received a lot of upvotes - it's a good thing that someone can smile on this.
    – mguima
    Dec 4 at 10:17




    @CramerTV Given the tone of the answer, I think he said "red current" in a humorous way, refering to a current that, back then, should be only in red cables. It is not fair to downvote this answer for this. Just upwards there is a humorous comment about energy runing fast in red wire that received a lot of upvotes - it's a good thing that someone can smile on this.
    – mguima
    Dec 4 at 10:17












    @CramerTV: it's even more confusing if you mix up words. Electrons flow from negative to positive voltage.
    – Guimoute
    Dec 7 at 10:14




    @CramerTV: it's even more confusing if you mix up words. Electrons flow from negative to positive voltage.
    – Guimoute
    Dec 7 at 10:14












    @mguima, While humor is a great thing in ordinary life, when giving answers I think it is important to ensure the answers are clear and unambiguous - especially for newbies and for those who don't speak English natively. These sites show up in nearly every country around the world and making them as clear and concise as possible is something I believe is important, especially when dealing with potentially dangerous things like electricity. Also, I did not downvote so am unsure why any mention of that was made.
    – CramerTV
    Dec 7 at 16:58






    @mguima, While humor is a great thing in ordinary life, when giving answers I think it is important to ensure the answers are clear and unambiguous - especially for newbies and for those who don't speak English natively. These sites show up in nearly every country around the world and making them as clear and concise as possible is something I believe is important, especially when dealing with potentially dangerous things like electricity. Also, I did not downvote so am unsure why any mention of that was made.
    – CramerTV
    Dec 7 at 16:58














    @mguima there's a difference of it being in an answer vs a comment, a comment which was deleted for some reason.
    – Passerby
    Dec 8 at 17:47






    @mguima there's a difference of it being in an answer vs a comment, a comment which was deleted for some reason.
    – Passerby
    Dec 8 at 17:47












    up vote
    6
    down vote













    There are some color code conventions for low voltage (<24V) DC wiring:
    Red is usually the positive supply line. Black is usually ground.
    If there are multiple positive supplies, they will have other hot colors applied (brown, yellow, orange).
    Pay attention that this is totally different from AC color codes. Do not mix these two under any circumstances.






    share|improve this answer





















    • An explanation about why not to mix these two under any circumstances would be a great addition to the answer.
      – WoJ
      Dec 3 at 21:39






    • 2




      Do Not assume these colours apply to cars... on some English cars brown is live (not fused) and on German cars brown is earth or ground... :) hours of fun sorting out burnt wires after getting those mixed up...
      – Solar Mike
      Dec 3 at 22:27










    • Just an addition: in computer hardware, usually yellow is 12v, orange is 3.3v, and red is 5v. I've never seen an environment where those three voltages were present, and this pattern wasn't used.
      – mguima
      Dec 4 at 10:19








    • 3




      @WoJ Well I know of at least four different AC color codes (US, old German, old UK, European standard), and I suspect there are many more. They are all incompatible.
      – Martin Bonner
      Dec 4 at 13:04






    • 1




      @MartinBonner I believe USSR/China uses green as a phase colour.
      – Someone Somewhere
      Dec 5 at 7:52















    up vote
    6
    down vote













    There are some color code conventions for low voltage (<24V) DC wiring:
    Red is usually the positive supply line. Black is usually ground.
    If there are multiple positive supplies, they will have other hot colors applied (brown, yellow, orange).
    Pay attention that this is totally different from AC color codes. Do not mix these two under any circumstances.






    share|improve this answer





















    • An explanation about why not to mix these two under any circumstances would be a great addition to the answer.
      – WoJ
      Dec 3 at 21:39






    • 2




      Do Not assume these colours apply to cars... on some English cars brown is live (not fused) and on German cars brown is earth or ground... :) hours of fun sorting out burnt wires after getting those mixed up...
      – Solar Mike
      Dec 3 at 22:27










    • Just an addition: in computer hardware, usually yellow is 12v, orange is 3.3v, and red is 5v. I've never seen an environment where those three voltages were present, and this pattern wasn't used.
      – mguima
      Dec 4 at 10:19








    • 3




      @WoJ Well I know of at least four different AC color codes (US, old German, old UK, European standard), and I suspect there are many more. They are all incompatible.
      – Martin Bonner
      Dec 4 at 13:04






    • 1




      @MartinBonner I believe USSR/China uses green as a phase colour.
      – Someone Somewhere
      Dec 5 at 7:52













    up vote
    6
    down vote










    up vote
    6
    down vote









    There are some color code conventions for low voltage (<24V) DC wiring:
    Red is usually the positive supply line. Black is usually ground.
    If there are multiple positive supplies, they will have other hot colors applied (brown, yellow, orange).
    Pay attention that this is totally different from AC color codes. Do not mix these two under any circumstances.






    share|improve this answer












    There are some color code conventions for low voltage (<24V) DC wiring:
    Red is usually the positive supply line. Black is usually ground.
    If there are multiple positive supplies, they will have other hot colors applied (brown, yellow, orange).
    Pay attention that this is totally different from AC color codes. Do not mix these two under any circumstances.







    share|improve this answer












    share|improve this answer



    share|improve this answer










    answered Dec 3 at 16:35









    Lior Bilia

    4,50411024




    4,50411024












    • An explanation about why not to mix these two under any circumstances would be a great addition to the answer.
      – WoJ
      Dec 3 at 21:39






    • 2




      Do Not assume these colours apply to cars... on some English cars brown is live (not fused) and on German cars brown is earth or ground... :) hours of fun sorting out burnt wires after getting those mixed up...
      – Solar Mike
      Dec 3 at 22:27










    • Just an addition: in computer hardware, usually yellow is 12v, orange is 3.3v, and red is 5v. I've never seen an environment where those three voltages were present, and this pattern wasn't used.
      – mguima
      Dec 4 at 10:19








    • 3




      @WoJ Well I know of at least four different AC color codes (US, old German, old UK, European standard), and I suspect there are many more. They are all incompatible.
      – Martin Bonner
      Dec 4 at 13:04






    • 1




      @MartinBonner I believe USSR/China uses green as a phase colour.
      – Someone Somewhere
      Dec 5 at 7:52


















    • An explanation about why not to mix these two under any circumstances would be a great addition to the answer.
      – WoJ
      Dec 3 at 21:39






    • 2




      Do Not assume these colours apply to cars... on some English cars brown is live (not fused) and on German cars brown is earth or ground... :) hours of fun sorting out burnt wires after getting those mixed up...
      – Solar Mike
      Dec 3 at 22:27










    • Just an addition: in computer hardware, usually yellow is 12v, orange is 3.3v, and red is 5v. I've never seen an environment where those three voltages were present, and this pattern wasn't used.
      – mguima
      Dec 4 at 10:19








    • 3




      @WoJ Well I know of at least four different AC color codes (US, old German, old UK, European standard), and I suspect there are many more. They are all incompatible.
      – Martin Bonner
      Dec 4 at 13:04






    • 1




      @MartinBonner I believe USSR/China uses green as a phase colour.
      – Someone Somewhere
      Dec 5 at 7:52
















    An explanation about why not to mix these two under any circumstances would be a great addition to the answer.
    – WoJ
    Dec 3 at 21:39




    An explanation about why not to mix these two under any circumstances would be a great addition to the answer.
    – WoJ
    Dec 3 at 21:39




    2




    2




    Do Not assume these colours apply to cars... on some English cars brown is live (not fused) and on German cars brown is earth or ground... :) hours of fun sorting out burnt wires after getting those mixed up...
    – Solar Mike
    Dec 3 at 22:27




    Do Not assume these colours apply to cars... on some English cars brown is live (not fused) and on German cars brown is earth or ground... :) hours of fun sorting out burnt wires after getting those mixed up...
    – Solar Mike
    Dec 3 at 22:27












    Just an addition: in computer hardware, usually yellow is 12v, orange is 3.3v, and red is 5v. I've never seen an environment where those three voltages were present, and this pattern wasn't used.
    – mguima
    Dec 4 at 10:19






    Just an addition: in computer hardware, usually yellow is 12v, orange is 3.3v, and red is 5v. I've never seen an environment where those three voltages were present, and this pattern wasn't used.
    – mguima
    Dec 4 at 10:19






    3




    3




    @WoJ Well I know of at least four different AC color codes (US, old German, old UK, European standard), and I suspect there are many more. They are all incompatible.
    – Martin Bonner
    Dec 4 at 13:04




    @WoJ Well I know of at least four different AC color codes (US, old German, old UK, European standard), and I suspect there are many more. They are all incompatible.
    – Martin Bonner
    Dec 4 at 13:04




    1




    1




    @MartinBonner I believe USSR/China uses green as a phase colour.
    – Someone Somewhere
    Dec 5 at 7:52




    @MartinBonner I believe USSR/China uses green as a phase colour.
    – Someone Somewhere
    Dec 5 at 7:52










    up vote
    4
    down vote













    As noted, color does not matter, but it does make life easier when assembling and/or debugging.



    Insulation type Does matter - for High Voltages (think tube amplifiers), direct underground, high temperature environments, durability. And then wire type depending on usage - single wires for breadboard, bundles of say 2 or 4 wires (speaker cord, lamp cord, or 4 for telephone line), twisted pair wire in othernet cable (4 pairs), shielded wire (microphone cable), bundles inside inside shielding (security system wire), twisted pair inside shielding with power & Gnd (USB cable?).



    Then there's wire strands (single wire, not too flexible, or multiple strands, for more flexibility) and wire gage - 30 AWG single strand for wire-wrapping, 26 AWG solid for breadboard, #2 stranded (Car battery terminals) and all kinds of stuff in between.






    share|improve this answer























    • I've normally used 22 solid for breadboarding purposes, seems to fit into .1" pin headers nicely - perhaps there are different size breadboards that use 26awg?
      – user2813274
      Dec 4 at 2:54






    • 1




      I could be off a size or two on the breadboard wiring, has been a while since I've done any. Too thick tho and it just mashes the spring contacts apart and ruins them.
      – CrossRoads
      Dec 4 at 5:04






    • 1




      In the late 1970s I worked as a "wireman", wiring equipment for a company supplying the UK military. You would mount boards, connectors, switches, controls, etc, in a steel cabinet and then wire it all together using wires of specified length, in a harness, all laced together using "lacing cord", and all these wires were the same colour. Pink.
      – Michael Harvey
      Dec 4 at 19:41

















    up vote
    4
    down vote













    As noted, color does not matter, but it does make life easier when assembling and/or debugging.



    Insulation type Does matter - for High Voltages (think tube amplifiers), direct underground, high temperature environments, durability. And then wire type depending on usage - single wires for breadboard, bundles of say 2 or 4 wires (speaker cord, lamp cord, or 4 for telephone line), twisted pair wire in othernet cable (4 pairs), shielded wire (microphone cable), bundles inside inside shielding (security system wire), twisted pair inside shielding with power & Gnd (USB cable?).



    Then there's wire strands (single wire, not too flexible, or multiple strands, for more flexibility) and wire gage - 30 AWG single strand for wire-wrapping, 26 AWG solid for breadboard, #2 stranded (Car battery terminals) and all kinds of stuff in between.






    share|improve this answer























    • I've normally used 22 solid for breadboarding purposes, seems to fit into .1" pin headers nicely - perhaps there are different size breadboards that use 26awg?
      – user2813274
      Dec 4 at 2:54






    • 1




      I could be off a size or two on the breadboard wiring, has been a while since I've done any. Too thick tho and it just mashes the spring contacts apart and ruins them.
      – CrossRoads
      Dec 4 at 5:04






    • 1




      In the late 1970s I worked as a "wireman", wiring equipment for a company supplying the UK military. You would mount boards, connectors, switches, controls, etc, in a steel cabinet and then wire it all together using wires of specified length, in a harness, all laced together using "lacing cord", and all these wires were the same colour. Pink.
      – Michael Harvey
      Dec 4 at 19:41















    up vote
    4
    down vote










    up vote
    4
    down vote









    As noted, color does not matter, but it does make life easier when assembling and/or debugging.



    Insulation type Does matter - for High Voltages (think tube amplifiers), direct underground, high temperature environments, durability. And then wire type depending on usage - single wires for breadboard, bundles of say 2 or 4 wires (speaker cord, lamp cord, or 4 for telephone line), twisted pair wire in othernet cable (4 pairs), shielded wire (microphone cable), bundles inside inside shielding (security system wire), twisted pair inside shielding with power & Gnd (USB cable?).



    Then there's wire strands (single wire, not too flexible, or multiple strands, for more flexibility) and wire gage - 30 AWG single strand for wire-wrapping, 26 AWG solid for breadboard, #2 stranded (Car battery terminals) and all kinds of stuff in between.






    share|improve this answer














    As noted, color does not matter, but it does make life easier when assembling and/or debugging.



    Insulation type Does matter - for High Voltages (think tube amplifiers), direct underground, high temperature environments, durability. And then wire type depending on usage - single wires for breadboard, bundles of say 2 or 4 wires (speaker cord, lamp cord, or 4 for telephone line), twisted pair wire in othernet cable (4 pairs), shielded wire (microphone cable), bundles inside inside shielding (security system wire), twisted pair inside shielding with power & Gnd (USB cable?).



    Then there's wire strands (single wire, not too flexible, or multiple strands, for more flexibility) and wire gage - 30 AWG single strand for wire-wrapping, 26 AWG solid for breadboard, #2 stranded (Car battery terminals) and all kinds of stuff in between.







    share|improve this answer














    share|improve this answer



    share|improve this answer








    edited Dec 3 at 17:33

























    answered Dec 3 at 17:22









    CrossRoads

    1,0288




    1,0288












    • I've normally used 22 solid for breadboarding purposes, seems to fit into .1" pin headers nicely - perhaps there are different size breadboards that use 26awg?
      – user2813274
      Dec 4 at 2:54






    • 1




      I could be off a size or two on the breadboard wiring, has been a while since I've done any. Too thick tho and it just mashes the spring contacts apart and ruins them.
      – CrossRoads
      Dec 4 at 5:04






    • 1




      In the late 1970s I worked as a "wireman", wiring equipment for a company supplying the UK military. You would mount boards, connectors, switches, controls, etc, in a steel cabinet and then wire it all together using wires of specified length, in a harness, all laced together using "lacing cord", and all these wires were the same colour. Pink.
      – Michael Harvey
      Dec 4 at 19:41




















    • I've normally used 22 solid for breadboarding purposes, seems to fit into .1" pin headers nicely - perhaps there are different size breadboards that use 26awg?
      – user2813274
      Dec 4 at 2:54






    • 1




      I could be off a size or two on the breadboard wiring, has been a while since I've done any. Too thick tho and it just mashes the spring contacts apart and ruins them.
      – CrossRoads
      Dec 4 at 5:04






    • 1




      In the late 1970s I worked as a "wireman", wiring equipment for a company supplying the UK military. You would mount boards, connectors, switches, controls, etc, in a steel cabinet and then wire it all together using wires of specified length, in a harness, all laced together using "lacing cord", and all these wires were the same colour. Pink.
      – Michael Harvey
      Dec 4 at 19:41


















    I've normally used 22 solid for breadboarding purposes, seems to fit into .1" pin headers nicely - perhaps there are different size breadboards that use 26awg?
    – user2813274
    Dec 4 at 2:54




    I've normally used 22 solid for breadboarding purposes, seems to fit into .1" pin headers nicely - perhaps there are different size breadboards that use 26awg?
    – user2813274
    Dec 4 at 2:54




    1




    1




    I could be off a size or two on the breadboard wiring, has been a while since I've done any. Too thick tho and it just mashes the spring contacts apart and ruins them.
    – CrossRoads
    Dec 4 at 5:04




    I could be off a size or two on the breadboard wiring, has been a while since I've done any. Too thick tho and it just mashes the spring contacts apart and ruins them.
    – CrossRoads
    Dec 4 at 5:04




    1




    1




    In the late 1970s I worked as a "wireman", wiring equipment for a company supplying the UK military. You would mount boards, connectors, switches, controls, etc, in a steel cabinet and then wire it all together using wires of specified length, in a harness, all laced together using "lacing cord", and all these wires were the same colour. Pink.
    – Michael Harvey
    Dec 4 at 19:41






    In the late 1970s I worked as a "wireman", wiring equipment for a company supplying the UK military. You would mount boards, connectors, switches, controls, etc, in a steel cabinet and then wire it all together using wires of specified length, in a harness, all laced together using "lacing cord", and all these wires were the same colour. Pink.
    – Michael Harvey
    Dec 4 at 19:41












    up vote
    4
    down vote













    Low voltage and "inside the box", color does not matter too much. There are two situations though where there are standards, one of them very important:



    AC "Mains" Power



    Colors for AC power do vary somewhat around the world. In the US, the general colors are:




    • White or Gray = Neutral

    • Green or bare = Ground

    • All other colors = Hot. For a number of reasons, the most common colors typically for hot (at least in residential applications) are Black followed by Red.


    Anyone who works on 120V (and above) AC power should always treat any unknown wire as potentially hot, but when wiring is done properly, these standard colors help a lot to keep things straight and safe.



    "Standard" Power Supplies



    A classic example of de facto color coding is the ATX Power Supply. See the link for details, but it includes multiple wires of the same color for a given use including:




    • Orange = +3.3V

    • Black = Ground

    • Red = +5V

    • Yellow = +12V


    Most people will never do more with an ATX power supply than swap one for another, and the connector only fits one way. But if you need to splice into one or are trying to build your own or do something else out of the ordinary with it, then sticking to the standard colors can make your life much easier.






    share|improve this answer

















    • 3




      Just note that AC mains wire colours vary between countries. In the UK Blue is Neutral, Brown is Hot (as are Black and Grey in three phase). Old UK standard had Red as Hot and Black as Neutral. As ever, when in doubt refer to local standards.
      – Tom Carpenter
      Dec 3 at 22:45










    • Which is why I started off with Colors for AC power do vary somewhat around the world
      – manassehkatz
      Dec 3 at 23:17






    • 1




      missed that, my bad.
      – Tom Carpenter
      Dec 4 at 9:23






    • 2




      I think that the risk involved is inversely proportional to the reliability of the color codes. When dealing with AC, I think that is not advisable to consider that a wire is neutral only because it is white or gray (even if I did that installation myself - I confess that I would not swear that I've always observed the patterns). First thing to do is test / measure all the wires to discover if the color codes were used or not.
      – mguima
      Dec 4 at 10:03










    • Not to mention countries that have changed colour codes, such as the UK and much of Europe.
      – Someone Somewhere
      Dec 5 at 7:55















    up vote
    4
    down vote













    Low voltage and "inside the box", color does not matter too much. There are two situations though where there are standards, one of them very important:



    AC "Mains" Power



    Colors for AC power do vary somewhat around the world. In the US, the general colors are:




    • White or Gray = Neutral

    • Green or bare = Ground

    • All other colors = Hot. For a number of reasons, the most common colors typically for hot (at least in residential applications) are Black followed by Red.


    Anyone who works on 120V (and above) AC power should always treat any unknown wire as potentially hot, but when wiring is done properly, these standard colors help a lot to keep things straight and safe.



    "Standard" Power Supplies



    A classic example of de facto color coding is the ATX Power Supply. See the link for details, but it includes multiple wires of the same color for a given use including:




    • Orange = +3.3V

    • Black = Ground

    • Red = +5V

    • Yellow = +12V


    Most people will never do more with an ATX power supply than swap one for another, and the connector only fits one way. But if you need to splice into one or are trying to build your own or do something else out of the ordinary with it, then sticking to the standard colors can make your life much easier.






    share|improve this answer

















    • 3




      Just note that AC mains wire colours vary between countries. In the UK Blue is Neutral, Brown is Hot (as are Black and Grey in three phase). Old UK standard had Red as Hot and Black as Neutral. As ever, when in doubt refer to local standards.
      – Tom Carpenter
      Dec 3 at 22:45










    • Which is why I started off with Colors for AC power do vary somewhat around the world
      – manassehkatz
      Dec 3 at 23:17






    • 1




      missed that, my bad.
      – Tom Carpenter
      Dec 4 at 9:23






    • 2




      I think that the risk involved is inversely proportional to the reliability of the color codes. When dealing with AC, I think that is not advisable to consider that a wire is neutral only because it is white or gray (even if I did that installation myself - I confess that I would not swear that I've always observed the patterns). First thing to do is test / measure all the wires to discover if the color codes were used or not.
      – mguima
      Dec 4 at 10:03










    • Not to mention countries that have changed colour codes, such as the UK and much of Europe.
      – Someone Somewhere
      Dec 5 at 7:55













    up vote
    4
    down vote










    up vote
    4
    down vote









    Low voltage and "inside the box", color does not matter too much. There are two situations though where there are standards, one of them very important:



    AC "Mains" Power



    Colors for AC power do vary somewhat around the world. In the US, the general colors are:




    • White or Gray = Neutral

    • Green or bare = Ground

    • All other colors = Hot. For a number of reasons, the most common colors typically for hot (at least in residential applications) are Black followed by Red.


    Anyone who works on 120V (and above) AC power should always treat any unknown wire as potentially hot, but when wiring is done properly, these standard colors help a lot to keep things straight and safe.



    "Standard" Power Supplies



    A classic example of de facto color coding is the ATX Power Supply. See the link for details, but it includes multiple wires of the same color for a given use including:




    • Orange = +3.3V

    • Black = Ground

    • Red = +5V

    • Yellow = +12V


    Most people will never do more with an ATX power supply than swap one for another, and the connector only fits one way. But if you need to splice into one or are trying to build your own or do something else out of the ordinary with it, then sticking to the standard colors can make your life much easier.






    share|improve this answer












    Low voltage and "inside the box", color does not matter too much. There are two situations though where there are standards, one of them very important:



    AC "Mains" Power



    Colors for AC power do vary somewhat around the world. In the US, the general colors are:




    • White or Gray = Neutral

    • Green or bare = Ground

    • All other colors = Hot. For a number of reasons, the most common colors typically for hot (at least in residential applications) are Black followed by Red.


    Anyone who works on 120V (and above) AC power should always treat any unknown wire as potentially hot, but when wiring is done properly, these standard colors help a lot to keep things straight and safe.



    "Standard" Power Supplies



    A classic example of de facto color coding is the ATX Power Supply. See the link for details, but it includes multiple wires of the same color for a given use including:




    • Orange = +3.3V

    • Black = Ground

    • Red = +5V

    • Yellow = +12V


    Most people will never do more with an ATX power supply than swap one for another, and the connector only fits one way. But if you need to splice into one or are trying to build your own or do something else out of the ordinary with it, then sticking to the standard colors can make your life much easier.







    share|improve this answer












    share|improve this answer



    share|improve this answer










    answered Dec 3 at 22:21









    manassehkatz

    26916




    26916








    • 3




      Just note that AC mains wire colours vary between countries. In the UK Blue is Neutral, Brown is Hot (as are Black and Grey in three phase). Old UK standard had Red as Hot and Black as Neutral. As ever, when in doubt refer to local standards.
      – Tom Carpenter
      Dec 3 at 22:45










    • Which is why I started off with Colors for AC power do vary somewhat around the world
      – manassehkatz
      Dec 3 at 23:17






    • 1




      missed that, my bad.
      – Tom Carpenter
      Dec 4 at 9:23






    • 2




      I think that the risk involved is inversely proportional to the reliability of the color codes. When dealing with AC, I think that is not advisable to consider that a wire is neutral only because it is white or gray (even if I did that installation myself - I confess that I would not swear that I've always observed the patterns). First thing to do is test / measure all the wires to discover if the color codes were used or not.
      – mguima
      Dec 4 at 10:03










    • Not to mention countries that have changed colour codes, such as the UK and much of Europe.
      – Someone Somewhere
      Dec 5 at 7:55














    • 3




      Just note that AC mains wire colours vary between countries. In the UK Blue is Neutral, Brown is Hot (as are Black and Grey in three phase). Old UK standard had Red as Hot and Black as Neutral. As ever, when in doubt refer to local standards.
      – Tom Carpenter
      Dec 3 at 22:45










    • Which is why I started off with Colors for AC power do vary somewhat around the world
      – manassehkatz
      Dec 3 at 23:17






    • 1




      missed that, my bad.
      – Tom Carpenter
      Dec 4 at 9:23






    • 2




      I think that the risk involved is inversely proportional to the reliability of the color codes. When dealing with AC, I think that is not advisable to consider that a wire is neutral only because it is white or gray (even if I did that installation myself - I confess that I would not swear that I've always observed the patterns). First thing to do is test / measure all the wires to discover if the color codes were used or not.
      – mguima
      Dec 4 at 10:03










    • Not to mention countries that have changed colour codes, such as the UK and much of Europe.
      – Someone Somewhere
      Dec 5 at 7:55








    3




    3




    Just note that AC mains wire colours vary between countries. In the UK Blue is Neutral, Brown is Hot (as are Black and Grey in three phase). Old UK standard had Red as Hot and Black as Neutral. As ever, when in doubt refer to local standards.
    – Tom Carpenter
    Dec 3 at 22:45




    Just note that AC mains wire colours vary between countries. In the UK Blue is Neutral, Brown is Hot (as are Black and Grey in three phase). Old UK standard had Red as Hot and Black as Neutral. As ever, when in doubt refer to local standards.
    – Tom Carpenter
    Dec 3 at 22:45












    Which is why I started off with Colors for AC power do vary somewhat around the world
    – manassehkatz
    Dec 3 at 23:17




    Which is why I started off with Colors for AC power do vary somewhat around the world
    – manassehkatz
    Dec 3 at 23:17




    1




    1




    missed that, my bad.
    – Tom Carpenter
    Dec 4 at 9:23




    missed that, my bad.
    – Tom Carpenter
    Dec 4 at 9:23




    2




    2




    I think that the risk involved is inversely proportional to the reliability of the color codes. When dealing with AC, I think that is not advisable to consider that a wire is neutral only because it is white or gray (even if I did that installation myself - I confess that I would not swear that I've always observed the patterns). First thing to do is test / measure all the wires to discover if the color codes were used or not.
    – mguima
    Dec 4 at 10:03




    I think that the risk involved is inversely proportional to the reliability of the color codes. When dealing with AC, I think that is not advisable to consider that a wire is neutral only because it is white or gray (even if I did that installation myself - I confess that I would not swear that I've always observed the patterns). First thing to do is test / measure all the wires to discover if the color codes were used or not.
    – mguima
    Dec 4 at 10:03












    Not to mention countries that have changed colour codes, such as the UK and much of Europe.
    – Someone Somewhere
    Dec 5 at 7:55




    Not to mention countries that have changed colour codes, such as the UK and much of Europe.
    – Someone Somewhere
    Dec 5 at 7:55










    up vote
    4
    down vote













    Yes, the wire colors matter - just imagine when agent 007 opens up the box where there are 7 seconds left on the timer, wire cutters in hand, asks "which wire do I cut, they are all the same shade of grey?"



    Unless you are a diabolical bomb maker & your intentions are to obfuscate your design, sticking to standard colors is highly reccomended for not just others, but even yourself to understand what you have done






    share|improve this answer

















    • 6




      And if you are a diabolical bomb maker and you use all grey wires, sooner or later you will blow yourself up.
      – A. I. Breveleri
      Dec 4 at 4:15






    • 2




      Just never cut the red wire!
      – davidbak
      Dec 4 at 4:33






    • 1




      @A.I.Breveleri the chances of blowing yourself up as a diabolical bomb maker are high either way, but provided you use some other means of organisation (and properly test the circuits without live explosive attached), that risk doesn't go up that much more by the use of grey wires only.
      – leftaroundabout
      Dec 4 at 10:10






    • 1




      @davidbak it's considered good etiquette to put a big warning before any TVTropes link you post on StackExchange... like you also wouldn't pack a mail bomb without an “explosive hazard” sign, right? (Or with all-grey wiring...)
      – leftaroundabout
      Dec 4 at 10:16






    • 1




      @davidbak The Evil Overlord list provides plenty of advice. #15 seems applicable here. From cellblock A, #136 applies to OP's scenario. Warning: TV Tropes.
      – a CVn
      Dec 4 at 14:46

















    up vote
    4
    down vote













    Yes, the wire colors matter - just imagine when agent 007 opens up the box where there are 7 seconds left on the timer, wire cutters in hand, asks "which wire do I cut, they are all the same shade of grey?"



    Unless you are a diabolical bomb maker & your intentions are to obfuscate your design, sticking to standard colors is highly reccomended for not just others, but even yourself to understand what you have done






    share|improve this answer

















    • 6




      And if you are a diabolical bomb maker and you use all grey wires, sooner or later you will blow yourself up.
      – A. I. Breveleri
      Dec 4 at 4:15






    • 2




      Just never cut the red wire!
      – davidbak
      Dec 4 at 4:33






    • 1




      @A.I.Breveleri the chances of blowing yourself up as a diabolical bomb maker are high either way, but provided you use some other means of organisation (and properly test the circuits without live explosive attached), that risk doesn't go up that much more by the use of grey wires only.
      – leftaroundabout
      Dec 4 at 10:10






    • 1




      @davidbak it's considered good etiquette to put a big warning before any TVTropes link you post on StackExchange... like you also wouldn't pack a mail bomb without an “explosive hazard” sign, right? (Or with all-grey wiring...)
      – leftaroundabout
      Dec 4 at 10:16






    • 1




      @davidbak The Evil Overlord list provides plenty of advice. #15 seems applicable here. From cellblock A, #136 applies to OP's scenario. Warning: TV Tropes.
      – a CVn
      Dec 4 at 14:46















    up vote
    4
    down vote










    up vote
    4
    down vote









    Yes, the wire colors matter - just imagine when agent 007 opens up the box where there are 7 seconds left on the timer, wire cutters in hand, asks "which wire do I cut, they are all the same shade of grey?"



    Unless you are a diabolical bomb maker & your intentions are to obfuscate your design, sticking to standard colors is highly reccomended for not just others, but even yourself to understand what you have done






    share|improve this answer












    Yes, the wire colors matter - just imagine when agent 007 opens up the box where there are 7 seconds left on the timer, wire cutters in hand, asks "which wire do I cut, they are all the same shade of grey?"



    Unless you are a diabolical bomb maker & your intentions are to obfuscate your design, sticking to standard colors is highly reccomended for not just others, but even yourself to understand what you have done







    share|improve this answer












    share|improve this answer



    share|improve this answer










    answered Dec 4 at 2:52









    user2813274

    410320




    410320








    • 6




      And if you are a diabolical bomb maker and you use all grey wires, sooner or later you will blow yourself up.
      – A. I. Breveleri
      Dec 4 at 4:15






    • 2




      Just never cut the red wire!
      – davidbak
      Dec 4 at 4:33






    • 1




      @A.I.Breveleri the chances of blowing yourself up as a diabolical bomb maker are high either way, but provided you use some other means of organisation (and properly test the circuits without live explosive attached), that risk doesn't go up that much more by the use of grey wires only.
      – leftaroundabout
      Dec 4 at 10:10






    • 1




      @davidbak it's considered good etiquette to put a big warning before any TVTropes link you post on StackExchange... like you also wouldn't pack a mail bomb without an “explosive hazard” sign, right? (Or with all-grey wiring...)
      – leftaroundabout
      Dec 4 at 10:16






    • 1




      @davidbak The Evil Overlord list provides plenty of advice. #15 seems applicable here. From cellblock A, #136 applies to OP's scenario. Warning: TV Tropes.
      – a CVn
      Dec 4 at 14:46
















    • 6




      And if you are a diabolical bomb maker and you use all grey wires, sooner or later you will blow yourself up.
      – A. I. Breveleri
      Dec 4 at 4:15






    • 2




      Just never cut the red wire!
      – davidbak
      Dec 4 at 4:33






    • 1




      @A.I.Breveleri the chances of blowing yourself up as a diabolical bomb maker are high either way, but provided you use some other means of organisation (and properly test the circuits without live explosive attached), that risk doesn't go up that much more by the use of grey wires only.
      – leftaroundabout
      Dec 4 at 10:10






    • 1




      @davidbak it's considered good etiquette to put a big warning before any TVTropes link you post on StackExchange... like you also wouldn't pack a mail bomb without an “explosive hazard” sign, right? (Or with all-grey wiring...)
      – leftaroundabout
      Dec 4 at 10:16






    • 1




      @davidbak The Evil Overlord list provides plenty of advice. #15 seems applicable here. From cellblock A, #136 applies to OP's scenario. Warning: TV Tropes.
      – a CVn
      Dec 4 at 14:46










    6




    6




    And if you are a diabolical bomb maker and you use all grey wires, sooner or later you will blow yourself up.
    – A. I. Breveleri
    Dec 4 at 4:15




    And if you are a diabolical bomb maker and you use all grey wires, sooner or later you will blow yourself up.
    – A. I. Breveleri
    Dec 4 at 4:15




    2




    2




    Just never cut the red wire!
    – davidbak
    Dec 4 at 4:33




    Just never cut the red wire!
    – davidbak
    Dec 4 at 4:33




    1




    1




    @A.I.Breveleri the chances of blowing yourself up as a diabolical bomb maker are high either way, but provided you use some other means of organisation (and properly test the circuits without live explosive attached), that risk doesn't go up that much more by the use of grey wires only.
    – leftaroundabout
    Dec 4 at 10:10




    @A.I.Breveleri the chances of blowing yourself up as a diabolical bomb maker are high either way, but provided you use some other means of organisation (and properly test the circuits without live explosive attached), that risk doesn't go up that much more by the use of grey wires only.
    – leftaroundabout
    Dec 4 at 10:10




    1




    1




    @davidbak it's considered good etiquette to put a big warning before any TVTropes link you post on StackExchange... like you also wouldn't pack a mail bomb without an “explosive hazard” sign, right? (Or with all-grey wiring...)
    – leftaroundabout
    Dec 4 at 10:16




    @davidbak it's considered good etiquette to put a big warning before any TVTropes link you post on StackExchange... like you also wouldn't pack a mail bomb without an “explosive hazard” sign, right? (Or with all-grey wiring...)
    – leftaroundabout
    Dec 4 at 10:16




    1




    1




    @davidbak The Evil Overlord list provides plenty of advice. #15 seems applicable here. From cellblock A, #136 applies to OP's scenario. Warning: TV Tropes.
    – a CVn
    Dec 4 at 14:46






    @davidbak The Evil Overlord list provides plenty of advice. #15 seems applicable here. From cellblock A, #136 applies to OP's scenario. Warning: TV Tropes.
    – a CVn
    Dec 4 at 14:46












    up vote
    4
    down vote













    Mark 'em yourself



    enter image description here



    This 5-pack of electrical tape is $4.



    You don't have any particular obligation in homebrew electronics wiring (except to yourself, as confusing wires will waste a LOT of your time). The convention is red for positive and black for negative, particularly in a negative ground context.



    However in mains wiring, you have some obligatory colors.




    • Equipment safety earthing must be green, green/yellow or bare.

    • If an active conductor is near earth voltage, it is called neutral, and it must be white or gray in North America or Philippines, and light blue in the rest of the world (black in Au/NZ).

    • "hot compared to earth" conductors are particular colors: much of the world brown then black then gray, North America any unreserved color (except orange for the high leg in 240V wild-leg) but convention is black then red then blue.






    share|improve this answer





















    • Also, in North America, the three colors used for well pump wires are usually red, black and yellow.
      – mkeith
      Dec 8 at 2:51

















    up vote
    4
    down vote













    Mark 'em yourself



    enter image description here



    This 5-pack of electrical tape is $4.



    You don't have any particular obligation in homebrew electronics wiring (except to yourself, as confusing wires will waste a LOT of your time). The convention is red for positive and black for negative, particularly in a negative ground context.



    However in mains wiring, you have some obligatory colors.




    • Equipment safety earthing must be green, green/yellow or bare.

    • If an active conductor is near earth voltage, it is called neutral, and it must be white or gray in North America or Philippines, and light blue in the rest of the world (black in Au/NZ).

    • "hot compared to earth" conductors are particular colors: much of the world brown then black then gray, North America any unreserved color (except orange for the high leg in 240V wild-leg) but convention is black then red then blue.






    share|improve this answer





















    • Also, in North America, the three colors used for well pump wires are usually red, black and yellow.
      – mkeith
      Dec 8 at 2:51















    up vote
    4
    down vote










    up vote
    4
    down vote









    Mark 'em yourself



    enter image description here



    This 5-pack of electrical tape is $4.



    You don't have any particular obligation in homebrew electronics wiring (except to yourself, as confusing wires will waste a LOT of your time). The convention is red for positive and black for negative, particularly in a negative ground context.



    However in mains wiring, you have some obligatory colors.




    • Equipment safety earthing must be green, green/yellow or bare.

    • If an active conductor is near earth voltage, it is called neutral, and it must be white or gray in North America or Philippines, and light blue in the rest of the world (black in Au/NZ).

    • "hot compared to earth" conductors are particular colors: much of the world brown then black then gray, North America any unreserved color (except orange for the high leg in 240V wild-leg) but convention is black then red then blue.






    share|improve this answer












    Mark 'em yourself



    enter image description here



    This 5-pack of electrical tape is $4.



    You don't have any particular obligation in homebrew electronics wiring (except to yourself, as confusing wires will waste a LOT of your time). The convention is red for positive and black for negative, particularly in a negative ground context.



    However in mains wiring, you have some obligatory colors.




    • Equipment safety earthing must be green, green/yellow or bare.

    • If an active conductor is near earth voltage, it is called neutral, and it must be white or gray in North America or Philippines, and light blue in the rest of the world (black in Au/NZ).

    • "hot compared to earth" conductors are particular colors: much of the world brown then black then gray, North America any unreserved color (except orange for the high leg in 240V wild-leg) but convention is black then red then blue.







    share|improve this answer












    share|improve this answer



    share|improve this answer










    answered Dec 6 at 5:59









    Harper

    5,819625




    5,819625












    • Also, in North America, the three colors used for well pump wires are usually red, black and yellow.
      – mkeith
      Dec 8 at 2:51




















    • Also, in North America, the three colors used for well pump wires are usually red, black and yellow.
      – mkeith
      Dec 8 at 2:51


















    Also, in North America, the three colors used for well pump wires are usually red, black and yellow.
    – mkeith
    Dec 8 at 2:51






    Also, in North America, the three colors used for well pump wires are usually red, black and yellow.
    – mkeith
    Dec 8 at 2:51












    up vote
    1
    down vote













    Color codes in wiring are regulated by ISO IEC 60445: 2017 "Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors".




    IEC 60445:2017 applies to the identification and marking of terminals
    of electrical equipment such as resistors, fuses, relays, contactors,
    transformers, rotating machines and, wherever applicable, to
    combinations of such equipment (e.g. assemblies), and also applies to
    the identification of terminations of certain designated conductors.
    It also provides general rules for the use of certain colours or
    alphanumeric notations to identify conductors with the aim of avoiding
    ambiguity and ensuring safe operation. These conductor colours or
    alphanumeric notations are intended to be applied in cables or cores,
    busbars, electrical equipment and installations. This basic safety
    publication is primarily intended for use by technical committees in
    the preparation of standards in accordance with the principles laid
    down in IEC Guide 104 and ISO/IEC Guide 51. It has the status of a
    basic safety publication in accordance with IEC Guide 104. This sixth
    edition cancels and replaces the fifth edition of IEC 60445, published
    in 2010.




    In EU - and surely in Italy, were I live - standard norms issued by ISO, EN and UNI (Italian National Standards Organization) have force of law, and whoever wants to build anything must comply with all relevant and applicable standard norms.



    In particular, compliancy with safety publications is strictly mandatory. Failure to comply will certainly lead to liability and prosecution in case of damages and/or injuries, not to mention death.



    So, the answer is, "yes, wire colors matter in electronics"






    share|improve this answer








    New contributor




    iw1dov is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
    Check out our Code of Conduct.






















      up vote
      1
      down vote













      Color codes in wiring are regulated by ISO IEC 60445: 2017 "Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors".




      IEC 60445:2017 applies to the identification and marking of terminals
      of electrical equipment such as resistors, fuses, relays, contactors,
      transformers, rotating machines and, wherever applicable, to
      combinations of such equipment (e.g. assemblies), and also applies to
      the identification of terminations of certain designated conductors.
      It also provides general rules for the use of certain colours or
      alphanumeric notations to identify conductors with the aim of avoiding
      ambiguity and ensuring safe operation. These conductor colours or
      alphanumeric notations are intended to be applied in cables or cores,
      busbars, electrical equipment and installations. This basic safety
      publication is primarily intended for use by technical committees in
      the preparation of standards in accordance with the principles laid
      down in IEC Guide 104 and ISO/IEC Guide 51. It has the status of a
      basic safety publication in accordance with IEC Guide 104. This sixth
      edition cancels and replaces the fifth edition of IEC 60445, published
      in 2010.




      In EU - and surely in Italy, were I live - standard norms issued by ISO, EN and UNI (Italian National Standards Organization) have force of law, and whoever wants to build anything must comply with all relevant and applicable standard norms.



      In particular, compliancy with safety publications is strictly mandatory. Failure to comply will certainly lead to liability and prosecution in case of damages and/or injuries, not to mention death.



      So, the answer is, "yes, wire colors matter in electronics"






      share|improve this answer








      New contributor




      iw1dov is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
      Check out our Code of Conduct.




















        up vote
        1
        down vote










        up vote
        1
        down vote









        Color codes in wiring are regulated by ISO IEC 60445: 2017 "Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors".




        IEC 60445:2017 applies to the identification and marking of terminals
        of electrical equipment such as resistors, fuses, relays, contactors,
        transformers, rotating machines and, wherever applicable, to
        combinations of such equipment (e.g. assemblies), and also applies to
        the identification of terminations of certain designated conductors.
        It also provides general rules for the use of certain colours or
        alphanumeric notations to identify conductors with the aim of avoiding
        ambiguity and ensuring safe operation. These conductor colours or
        alphanumeric notations are intended to be applied in cables or cores,
        busbars, electrical equipment and installations. This basic safety
        publication is primarily intended for use by technical committees in
        the preparation of standards in accordance with the principles laid
        down in IEC Guide 104 and ISO/IEC Guide 51. It has the status of a
        basic safety publication in accordance with IEC Guide 104. This sixth
        edition cancels and replaces the fifth edition of IEC 60445, published
        in 2010.




        In EU - and surely in Italy, were I live - standard norms issued by ISO, EN and UNI (Italian National Standards Organization) have force of law, and whoever wants to build anything must comply with all relevant and applicable standard norms.



        In particular, compliancy with safety publications is strictly mandatory. Failure to comply will certainly lead to liability and prosecution in case of damages and/or injuries, not to mention death.



        So, the answer is, "yes, wire colors matter in electronics"






        share|improve this answer








        New contributor




        iw1dov is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.









        Color codes in wiring are regulated by ISO IEC 60445: 2017 "Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors".




        IEC 60445:2017 applies to the identification and marking of terminals
        of electrical equipment such as resistors, fuses, relays, contactors,
        transformers, rotating machines and, wherever applicable, to
        combinations of such equipment (e.g. assemblies), and also applies to
        the identification of terminations of certain designated conductors.
        It also provides general rules for the use of certain colours or
        alphanumeric notations to identify conductors with the aim of avoiding
        ambiguity and ensuring safe operation. These conductor colours or
        alphanumeric notations are intended to be applied in cables or cores,
        busbars, electrical equipment and installations. This basic safety
        publication is primarily intended for use by technical committees in
        the preparation of standards in accordance with the principles laid
        down in IEC Guide 104 and ISO/IEC Guide 51. It has the status of a
        basic safety publication in accordance with IEC Guide 104. This sixth
        edition cancels and replaces the fifth edition of IEC 60445, published
        in 2010.




        In EU - and surely in Italy, were I live - standard norms issued by ISO, EN and UNI (Italian National Standards Organization) have force of law, and whoever wants to build anything must comply with all relevant and applicable standard norms.



        In particular, compliancy with safety publications is strictly mandatory. Failure to comply will certainly lead to liability and prosecution in case of damages and/or injuries, not to mention death.



        So, the answer is, "yes, wire colors matter in electronics"







        share|improve this answer








        New contributor




        iw1dov is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.









        share|improve this answer



        share|improve this answer






        New contributor




        iw1dov is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.









        answered Dec 7 at 14:04









        iw1dov

        111




        111




        New contributor




        iw1dov is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.





        New contributor





        iw1dov is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.






        iw1dov is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
        Check out our Code of Conduct.






























            draft saved

            draft discarded




















































            Thanks for contributing an answer to Electrical Engineering Stack Exchange!


            • Please be sure to answer the question. Provide details and share your research!

            But avoid



            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.


            Use MathJax to format equations. MathJax reference.


            To learn more, see our tips on writing great answers.





            Some of your past answers have not been well-received, and you're in danger of being blocked from answering.


            Please pay close attention to the following guidance:


            • Please be sure to answer the question. Provide details and share your research!

            But avoid



            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.


            To learn more, see our tips on writing great answers.




            draft saved


            draft discarded














            StackExchange.ready(
            function () {
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f410213%2fdoes-wire-color-matter-in-electronics%23new-answer', 'question_page');
            }
            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown







            Popular posts from this blog

            Probability when a professor distributes a quiz and homework assignment to a class of n students.

            Aardman Animations

            Are they similar matrix