3" perfect wooden round hole in cabinet
.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty{ margin-bottom:0;
}
up vote
1
down vote
favorite
I need to make good round 3 inches hole in the wooden cabinet (see blue circle) to pass feed and load wires to a subpanel I'll put outside the cabinet.
What's the best way to make that hole? My carpenter planned to just hammer it with nail to create rough hole but it is not pure hard wood and I'm afraid the impact may make the cabinet misaligned. Is there a better way? Can I drill around the circle circumference with a small metal or concrete drill bit? What do you do?
carpentry
asked Nov 18 at 0:13
Samzun
5217
add a comment |
up vote
1
down vote
favorite
I need to make good round 3 inches hole in the wooden cabinet (see blue circle) to pass feed and load wires to a subpanel I'll put outside the cabinet.
What's the best way to make that hole? My carpenter planned to just hammer it with nail to create rough hole but it is not pure hard wood and I'm afraid the impact may make the cabinet misaligned. Is there a better way? Can I drill around the circle circumference with a small metal or concrete drill bit? What do you do?
carpentry
asked Nov 18 at 0:13
Samzun
5217
add a comment |
up vote
1
down vote
favorite
up vote
1
down vote
favorite
I need to make good round 3 inches hole in the wooden cabinet (see blue circle) to pass feed and load wires to a subpanel I'll put outside the cabinet.
What's the best way to make that hole? My carpenter planned to just hammer it with nail to create rough hole but it is not pure hard wood and I'm afraid the impact may make the cabinet misaligned. Is there a better way? Can I drill around the circle circumference with a small metal or concrete drill bit? What do you do?
carpentry
asked Nov 18 at 0:13
Samzun
5217
I need to make good round 3 inches hole in the wooden cabinet (see blue circle) to pass feed and load wires to a subpanel I'll put outside the cabinet.
What's the best way to make that hole? My carpenter planned to just hammer it with nail to create rough hole but it is not pure hard wood and I'm afraid the impact may make the cabinet misaligned. Is there a better way? Can I drill around the circle circumference with a small metal or concrete drill bit? What do you do?
carpentry
carpentry
asked Nov 18 at 0:13
Samzun
5217
asked Nov 18 at 0:13
Samzun
5217
asked Nov 18 at 0:13
Samzun
5217
asked Nov 18 at 0:13
Samzun
5217
asked Nov 18 at 0:13
Samzun
5217
5217
add a comment |
add a comment |
1 Answer
1
active
oldest
votes
up vote
10
down vote
Use a 3" hole saw or closest metric size on a drill. 3 inch hole saw
Use whatever tools you use to make a round hole in a door for a lock.
EDIT
What is on the other side of the cabinet where you want the hole? Is it open space or is it against a wall? I would say that pounding a nail repeatedly around a 3" diameter hole would likely damage the cabinet and maybe pull it apart at the joints. The right tool would be what used to be called a "keyhole saw" but is now usually called a "jab saw" (shown in the another answer, currently deleted). This tool is commonly used for drywall but can be used on other materials. You would drill a hole (say 3/8" or 1/2" diameter just inside the 3" circle and start sawing there.
Best jab saws
answered Nov 18 at 0:24
Jim Stewart
10.4k11129
I didn't know such thing exist. We don't have it on stock locally. Any other idea? Even a square hole would be ok.. but one just manually saws one side at a time.. is this effective too? What do you guys do if you don't have the machine hole saw?
– Samzun
Nov 18 at 0:28
2
I've used hole saws for a long time (at least 25 years). They're nothing new and I'm surprised you can't find them in your area. Brand doesn't matter - for a one-time use (though unless it falls apart, which it shouldn't, save it for the next time you need to drill a big hole) anything will do fine and they fit any battery or wired drill. But if you absolutely can't find a hole saw locally, just drill a starter hole with the largest regular bit you have and then use a sawzall (or equivalent) to cut out a square.
– manassehkatz
Nov 18 at 1:16
1
Any building supplier, hardware store, or electrical or plumbing supplier should be able to sell you one. I can think of a dozen chains in my city that carry them.
– Someone Somewhere
Nov 18 at 11:08
add a comment |
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
up vote
10
down vote
Use a 3" hole saw or closest metric size on a drill. 3 inch hole saw
Use whatever tools you use to make a round hole in a door for a lock.
EDIT
What is on the other side of the cabinet where you want the hole? Is it open space or is it against a wall? I would say that pounding a nail repeatedly around a 3" diameter hole would likely damage the cabinet and maybe pull it apart at the joints. The right tool would be what used to be called a "keyhole saw" but is now usually called a "jab saw" (shown in the another answer, currently deleted). This tool is commonly used for drywall but can be used on other materials. You would drill a hole (say 3/8" or 1/2" diameter just inside the 3" circle and start sawing there.
Best jab saws
answered Nov 18 at 0:24
Jim Stewart
10.4k11129
I didn't know such thing exist. We don't have it on stock locally. Any other idea? Even a square hole would be ok.. but one just manually saws one side at a time.. is this effective too? What do you guys do if you don't have the machine hole saw?
– Samzun
Nov 18 at 0:28
2
I've used hole saws for a long time (at least 25 years). They're nothing new and I'm surprised you can't find them in your area. Brand doesn't matter - for a one-time use (though unless it falls apart, which it shouldn't, save it for the next time you need to drill a big hole) anything will do fine and they fit any battery or wired drill. But if you absolutely can't find a hole saw locally, just drill a starter hole with the largest regular bit you have and then use a sawzall (or equivalent) to cut out a square.
– manassehkatz
Nov 18 at 1:16
1
Any building supplier, hardware store, or electrical or plumbing supplier should be able to sell you one. I can think of a dozen chains in my city that carry them.
– Someone Somewhere
Nov 18 at 11:08
add a comment |
up vote
10
down vote
Use a 3" hole saw or closest metric size on a drill. 3 inch hole saw
Use whatever tools you use to make a round hole in a door for a lock.
EDIT
What is on the other side of the cabinet where you want the hole? Is it open space or is it against a wall? I would say that pounding a nail repeatedly around a 3" diameter hole would likely damage the cabinet and maybe pull it apart at the joints. The right tool would be what used to be called a "keyhole saw" but is now usually called a "jab saw" (shown in the another answer, currently deleted). This tool is commonly used for drywall but can be used on other materials. You would drill a hole (say 3/8" or 1/2" diameter just inside the 3" circle and start sawing there.
Best jab saws
answered Nov 18 at 0:24
Jim Stewart
10.4k11129
I didn't know such thing exist. We don't have it on stock locally. Any other idea? Even a square hole would be ok.. but one just manually saws one side at a time.. is this effective too? What do you guys do if you don't have the machine hole saw?
– Samzun
Nov 18 at 0:28
2
I've used hole saws for a long time (at least 25 years). They're nothing new and I'm surprised you can't find them in your area. Brand doesn't matter - for a one-time use (though unless it falls apart, which it shouldn't, save it for the next time you need to drill a big hole) anything will do fine and they fit any battery or wired drill. But if you absolutely can't find a hole saw locally, just drill a starter hole with the largest regular bit you have and then use a sawzall (or equivalent) to cut out a square.
– manassehkatz
Nov 18 at 1:16
1
Any building supplier, hardware store, or electrical or plumbing supplier should be able to sell you one. I can think of a dozen chains in my city that carry them.
– Someone Somewhere
Nov 18 at 11:08
add a comment |
up vote
10
down vote
up vote
10
down vote
Use a 3" hole saw or closest metric size on a drill. 3 inch hole saw
Use whatever tools you use to make a round hole in a door for a lock.
EDIT
What is on the other side of the cabinet where you want the hole? Is it open space or is it against a wall? I would say that pounding a nail repeatedly around a 3" diameter hole would likely damage the cabinet and maybe pull it apart at the joints. The right tool would be what used to be called a "keyhole saw" but is now usually called a "jab saw" (shown in the another answer, currently deleted). This tool is commonly used for drywall but can be used on other materials. You would drill a hole (say 3/8" or 1/2" diameter just inside the 3" circle and start sawing there.
Best jab saws
answered Nov 18 at 0:24
Jim Stewart
10.4k11129
Use a 3" hole saw or closest metric size on a drill. 3 inch hole saw
Use whatever tools you use to make a round hole in a door for a lock.
EDIT
What is on the other side of the cabinet where you want the hole? Is it open space or is it against a wall? I would say that pounding a nail repeatedly around a 3" diameter hole would likely damage the cabinet and maybe pull it apart at the joints. The right tool would be what used to be called a "keyhole saw" but is now usually called a "jab saw" (shown in the another answer, currently deleted). This tool is commonly used for drywall but can be used on other materials. You would drill a hole (say 3/8" or 1/2" diameter just inside the 3" circle and start sawing there.
Best jab saws
answered Nov 18 at 0:24
Jim Stewart
10.4k11129
edited Nov 18 at 9:58
answered Nov 18 at 0:24
Jim Stewart
10.4k11129
answered Nov 18 at 0:24
Jim Stewart
10.4k11129
answered Nov 18 at 0:24
Jim Stewart
10.4k11129
10.4k11129
I didn't know such thing exist. We don't have it on stock locally. Any other idea? Even a square hole would be ok.. but one just manually saws one side at a time.. is this effective too? What do you guys do if you don't have the machine hole saw?
– Samzun
Nov 18 at 0:28
2
I've used hole saws for a long time (at least 25 years). They're nothing new and I'm surprised you can't find them in your area. Brand doesn't matter - for a one-time use (though unless it falls apart, which it shouldn't, save it for the next time you need to drill a big hole) anything will do fine and they fit any battery or wired drill. But if you absolutely can't find a hole saw locally, just drill a starter hole with the largest regular bit you have and then use a sawzall (or equivalent) to cut out a square.
– manassehkatz
Nov 18 at 1:16
1
Any building supplier, hardware store, or electrical or plumbing supplier should be able to sell you one. I can think of a dozen chains in my city that carry them.
– Someone Somewhere
Nov 18 at 11:08
add a comment |
I didn't know such thing exist. We don't have it on stock locally. Any other idea? Even a square hole would be ok.. but one just manually saws one side at a time.. is this effective too? What do you guys do if you don't have the machine hole saw?
– Samzun
Nov 18 at 0:28
2
I've used hole saws for a long time (at least 25 years). They're nothing new and I'm surprised you can't find them in your area. Brand doesn't matter - for a one-time use (though unless it falls apart, which it shouldn't, save it for the next time you need to drill a big hole) anything will do fine and they fit any battery or wired drill. But if you absolutely can't find a hole saw locally, just drill a starter hole with the largest regular bit you have and then use a sawzall (or equivalent) to cut out a square.
– manassehkatz
Nov 18 at 1:16
1
Any building supplier, hardware store, or electrical or plumbing supplier should be able to sell you one. I can think of a dozen chains in my city that carry them.
– Someone Somewhere
Nov 18 at 11:08
I didn't know such thing exist. We don't have it on stock locally. Any other idea? Even a square hole would be ok.. but one just manually saws one side at a time.. is this effective too? What do you guys do if you don't have the machine hole saw?
– Samzun
Nov 18 at 0:28
I didn't know such thing exist. We don't have it on stock locally. Any other idea? Even a square hole would be ok.. but one just manually saws one side at a time.. is this effective too? What do you guys do if you don't have the machine hole saw?
– Samzun
Nov 18 at 0:28
2
2
I've used hole saws for a long time (at least 25 years). They're nothing new and I'm surprised you can't find them in your area. Brand doesn't matter - for a one-time use (though unless it falls apart, which it shouldn't, save it for the next time you need to drill a big hole) anything will do fine and they fit any battery or wired drill. But if you absolutely can't find a hole saw locally, just drill a starter hole with the largest regular bit you have and then use a sawzall (or equivalent) to cut out a square.
– manassehkatz
Nov 18 at 1:16
I've used hole saws for a long time (at least 25 years). They're nothing new and I'm surprised you can't find them in your area. Brand doesn't matter - for a one-time use (though unless it falls apart, which it shouldn't, save it for the next time you need to drill a big hole) anything will do fine and they fit any battery or wired drill. But if you absolutely can't find a hole saw locally, just drill a starter hole with the largest regular bit you have and then use a sawzall (or equivalent) to cut out a square.
– manassehkatz
Nov 18 at 1:16
1
1
Any building supplier, hardware store, or electrical or plumbing supplier should be able to sell you one. I can think of a dozen chains in my city that carry them.
– Someone Somewhere
Nov 18 at 11:08
Any building supplier, hardware store, or electrical or plumbing supplier should be able to sell you one. I can think of a dozen chains in my city that carry them.
– Someone Somewhere
Nov 18 at 11:08
add a comment |
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f150803%2f3-perfect-wooden-round-hole-in-cabinet%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
