Hard drive not detected after installing the Operating System
After I failed to install SUSE Linux 10.0, I want to go back to the windows operating system again. but when I want to install windows, my hard drive is not detected, whereas in the BIOS in the detection / known. I was dizzy, his mistake about it. Where is.
I was looking for, my problem is named after the Blue Screen of Death (BSOD) that is an error message from windows to prevent further damage, but with various types of error messages, one of them as I have
*** STOP: 0X0000007B (0XF896A524, 0XC0000034, 0X00000000, 0X00000000)
I do not know, where the system is broken. but why hard drive is not known ... at the time of going to re-install?
hard-drive bios hardware-failure computer-building
|
show 3 more comments
After I failed to install SUSE Linux 10.0, I want to go back to the windows operating system again. but when I want to install windows, my hard drive is not detected, whereas in the BIOS in the detection / known. I was dizzy, his mistake about it. Where is.
I was looking for, my problem is named after the Blue Screen of Death (BSOD) that is an error message from windows to prevent further damage, but with various types of error messages, one of them as I have
*** STOP: 0X0000007B (0XF896A524, 0XC0000034, 0X00000000, 0X00000000)
I do not know, where the system is broken. but why hard drive is not known ... at the time of going to re-install?
hard-drive bios hardware-failure computer-building
1
Suse 10.0 is really old, and when i was using it, horribly buggy. In addition to that you really need to tell us more about your hard drive - sata or pata - and what version of windows you are trying to install (XP, vista or 7?)
– Journeyman Geek♦
Jun 6 '12 at 9:42
the night before I did install Windows XP SP2. Then the next morning, I tried to install linux and failed. Well that's where the problem began. what is kernel dump? I didn't know. Can you explain to me. Thank you
– Eka Anggraini
Jun 6 '12 at 10:08
kernel dump is BSOD on linux. I can try to help, but i need more details on hardware, like what sort of hard drive you have
– Journeyman Geek♦
Jun 6 '12 at 10:10
Thank you for your answer. I know now, Apparently my computer hard drive is not recognized by OS XP SP1, SP2 and SP3, due to be converted into serial SATA. But the windows 98 and windows vista can be installed. I'm confused until now, why could turn out that way. Was it because the failed installation of linux?
– Eka Anggraini
Jun 6 '12 at 10:56
If Windows Xp is not detecting the hard drive then you can try to install the Vista or 7. If they can detect the HDD then delete all the partitions and then recreate them through windows and then try to install XP again.
– avirk
Jun 6 '12 at 16:05
|
show 3 more comments
After I failed to install SUSE Linux 10.0, I want to go back to the windows operating system again. but when I want to install windows, my hard drive is not detected, whereas in the BIOS in the detection / known. I was dizzy, his mistake about it. Where is.
I was looking for, my problem is named after the Blue Screen of Death (BSOD) that is an error message from windows to prevent further damage, but with various types of error messages, one of them as I have
*** STOP: 0X0000007B (0XF896A524, 0XC0000034, 0X00000000, 0X00000000)
I do not know, where the system is broken. but why hard drive is not known ... at the time of going to re-install?
hard-drive bios hardware-failure computer-building
After I failed to install SUSE Linux 10.0, I want to go back to the windows operating system again. but when I want to install windows, my hard drive is not detected, whereas in the BIOS in the detection / known. I was dizzy, his mistake about it. Where is.
I was looking for, my problem is named after the Blue Screen of Death (BSOD) that is an error message from windows to prevent further damage, but with various types of error messages, one of them as I have
*** STOP: 0X0000007B (0XF896A524, 0XC0000034, 0X00000000, 0X00000000)
I do not know, where the system is broken. but why hard drive is not known ... at the time of going to re-install?
hard-drive bios hardware-failure computer-building
hard-drive bios hardware-failure computer-building
asked Jun 6 '12 at 8:57
Eka AnggrainiEka Anggraini
314
314
1
Suse 10.0 is really old, and when i was using it, horribly buggy. In addition to that you really need to tell us more about your hard drive - sata or pata - and what version of windows you are trying to install (XP, vista or 7?)
– Journeyman Geek♦
Jun 6 '12 at 9:42
the night before I did install Windows XP SP2. Then the next morning, I tried to install linux and failed. Well that's where the problem began. what is kernel dump? I didn't know. Can you explain to me. Thank you
– Eka Anggraini
Jun 6 '12 at 10:08
kernel dump is BSOD on linux. I can try to help, but i need more details on hardware, like what sort of hard drive you have
– Journeyman Geek♦
Jun 6 '12 at 10:10
Thank you for your answer. I know now, Apparently my computer hard drive is not recognized by OS XP SP1, SP2 and SP3, due to be converted into serial SATA. But the windows 98 and windows vista can be installed. I'm confused until now, why could turn out that way. Was it because the failed installation of linux?
– Eka Anggraini
Jun 6 '12 at 10:56
If Windows Xp is not detecting the hard drive then you can try to install the Vista or 7. If they can detect the HDD then delete all the partitions and then recreate them through windows and then try to install XP again.
– avirk
Jun 6 '12 at 16:05
|
show 3 more comments
1
Suse 10.0 is really old, and when i was using it, horribly buggy. In addition to that you really need to tell us more about your hard drive - sata or pata - and what version of windows you are trying to install (XP, vista or 7?)
– Journeyman Geek♦
Jun 6 '12 at 9:42
the night before I did install Windows XP SP2. Then the next morning, I tried to install linux and failed. Well that's where the problem began. what is kernel dump? I didn't know. Can you explain to me. Thank you
– Eka Anggraini
Jun 6 '12 at 10:08
kernel dump is BSOD on linux. I can try to help, but i need more details on hardware, like what sort of hard drive you have
– Journeyman Geek♦
Jun 6 '12 at 10:10
Thank you for your answer. I know now, Apparently my computer hard drive is not recognized by OS XP SP1, SP2 and SP3, due to be converted into serial SATA. But the windows 98 and windows vista can be installed. I'm confused until now, why could turn out that way. Was it because the failed installation of linux?
– Eka Anggraini
Jun 6 '12 at 10:56
If Windows Xp is not detecting the hard drive then you can try to install the Vista or 7. If they can detect the HDD then delete all the partitions and then recreate them through windows and then try to install XP again.
– avirk
Jun 6 '12 at 16:05
1
1
Suse 10.0 is really old, and when i was using it, horribly buggy. In addition to that you really need to tell us more about your hard drive - sata or pata - and what version of windows you are trying to install (XP, vista or 7?)
– Journeyman Geek♦
Jun 6 '12 at 9:42
Suse 10.0 is really old, and when i was using it, horribly buggy. In addition to that you really need to tell us more about your hard drive - sata or pata - and what version of windows you are trying to install (XP, vista or 7?)
– Journeyman Geek♦
Jun 6 '12 at 9:42
the night before I did install Windows XP SP2. Then the next morning, I tried to install linux and failed. Well that's where the problem began. what is kernel dump? I didn't know. Can you explain to me. Thank you
– Eka Anggraini
Jun 6 '12 at 10:08
the night before I did install Windows XP SP2. Then the next morning, I tried to install linux and failed. Well that's where the problem began. what is kernel dump? I didn't know. Can you explain to me. Thank you
– Eka Anggraini
Jun 6 '12 at 10:08
kernel dump is BSOD on linux. I can try to help, but i need more details on hardware, like what sort of hard drive you have
– Journeyman Geek♦
Jun 6 '12 at 10:10
kernel dump is BSOD on linux. I can try to help, but i need more details on hardware, like what sort of hard drive you have
– Journeyman Geek♦
Jun 6 '12 at 10:10
Thank you for your answer. I know now, Apparently my computer hard drive is not recognized by OS XP SP1, SP2 and SP3, due to be converted into serial SATA. But the windows 98 and windows vista can be installed. I'm confused until now, why could turn out that way. Was it because the failed installation of linux?
– Eka Anggraini
Jun 6 '12 at 10:56
Thank you for your answer. I know now, Apparently my computer hard drive is not recognized by OS XP SP1, SP2 and SP3, due to be converted into serial SATA. But the windows 98 and windows vista can be installed. I'm confused until now, why could turn out that way. Was it because the failed installation of linux?
– Eka Anggraini
Jun 6 '12 at 10:56
If Windows Xp is not detecting the hard drive then you can try to install the Vista or 7. If they can detect the HDD then delete all the partitions and then recreate them through windows and then try to install XP again.
– avirk
Jun 6 '12 at 16:05
If Windows Xp is not detecting the hard drive then you can try to install the Vista or 7. If they can detect the HDD then delete all the partitions and then recreate them through windows and then try to install XP again.
– avirk
Jun 6 '12 at 16:05
|
show 3 more comments
2 Answers
2
active
oldest
votes
In this scenario, i tend to wipe the drive with DBAN to ensure no bootloader related wierdness, then go one of two approaches. You don't actually need to let it do a full wipe - start it, wait 10 minutes or so, then just reboot and start with the install.
Windows XP dosen't support SATA out of the box, you'd need to go to the bios and disable AHCI, and select a legacy boot mode that will emulate a IDE interface. This is simpler, and needs no changes.
If you're a little more adventuous, you could integrate your drivers (and SP3!) with nlite from another windows system - since i don't know your motherboard, i'd suggest going with the chipset and hard drive sets from driverpacks.net. and sp3 from the network installation option from MS. I've linked the driverpacks instructions since its probably easier and better than any guide i could do
add a comment |
- You can use something like Hiren Boot cd.
- Or let it boot from SUSE first, when it wants to partition your hard try to delete all partitions you made with linux and reset your system after applying.
It should help you.
is it true? But where can I find the application (Hiren Boot cd). Thank you for your suggestion
– Eka Anggraini
Jun 6 '12 at 9:32
1
How exactly will hirens help? Which tool in hirens? What do you actually think she needs to do?
– Journeyman Geek♦
Jun 6 '12 at 9:47
O I know little what it is Hiren Boot cd. I have been searching for information across multiple sites. In there (Hiren boot CD) No information is that there are many other tools to repair the partition or disk. but inside full of illegal software compilations, such as partition magic, windows 98, windows 3.1, Acronis, Paragon, and so on ... technicians and weapons: tools & hard drive partitions, recover data, NTFS, file manager, and so forth. But I do not know the meaning clearly.
– Eka Anggraini
Jun 6 '12 at 10:23
1
So bad to see that my answer is -2. As a computer professional I just gave a point. If you google it a little, you will find exactly what you want. But as I should explain more, when hiren booted, tryHard Drive tools, about 7 tools I think. Partition magic for example (in old Versions). Or Paragon partiotion manager. Even you van boot your system with linux LIVE CD or any live cd. Then remove partitions and you are done, just apply and reboot.
– Hamed JML
Jun 6 '12 at 10:25
At last, I should say the only thing you need to do is to remove your partitions(partition table), and let windows to partition it. You can do it in about 1000 ways.
– Hamed JML
Jun 6 '12 at 10:35
|
show 1 more comment
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "3"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: true,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: 10,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f433272%2fhard-drive-not-detected-after-installing-the-operating-system%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
In this scenario, i tend to wipe the drive with DBAN to ensure no bootloader related wierdness, then go one of two approaches. You don't actually need to let it do a full wipe - start it, wait 10 minutes or so, then just reboot and start with the install.
Windows XP dosen't support SATA out of the box, you'd need to go to the bios and disable AHCI, and select a legacy boot mode that will emulate a IDE interface. This is simpler, and needs no changes.
If you're a little more adventuous, you could integrate your drivers (and SP3!) with nlite from another windows system - since i don't know your motherboard, i'd suggest going with the chipset and hard drive sets from driverpacks.net. and sp3 from the network installation option from MS. I've linked the driverpacks instructions since its probably easier and better than any guide i could do
add a comment |
In this scenario, i tend to wipe the drive with DBAN to ensure no bootloader related wierdness, then go one of two approaches. You don't actually need to let it do a full wipe - start it, wait 10 minutes or so, then just reboot and start with the install.
Windows XP dosen't support SATA out of the box, you'd need to go to the bios and disable AHCI, and select a legacy boot mode that will emulate a IDE interface. This is simpler, and needs no changes.
If you're a little more adventuous, you could integrate your drivers (and SP3!) with nlite from another windows system - since i don't know your motherboard, i'd suggest going with the chipset and hard drive sets from driverpacks.net. and sp3 from the network installation option from MS. I've linked the driverpacks instructions since its probably easier and better than any guide i could do
add a comment |
In this scenario, i tend to wipe the drive with DBAN to ensure no bootloader related wierdness, then go one of two approaches. You don't actually need to let it do a full wipe - start it, wait 10 minutes or so, then just reboot and start with the install.
Windows XP dosen't support SATA out of the box, you'd need to go to the bios and disable AHCI, and select a legacy boot mode that will emulate a IDE interface. This is simpler, and needs no changes.
If you're a little more adventuous, you could integrate your drivers (and SP3!) with nlite from another windows system - since i don't know your motherboard, i'd suggest going with the chipset and hard drive sets from driverpacks.net. and sp3 from the network installation option from MS. I've linked the driverpacks instructions since its probably easier and better than any guide i could do
In this scenario, i tend to wipe the drive with DBAN to ensure no bootloader related wierdness, then go one of two approaches. You don't actually need to let it do a full wipe - start it, wait 10 minutes or so, then just reboot and start with the install.
Windows XP dosen't support SATA out of the box, you'd need to go to the bios and disable AHCI, and select a legacy boot mode that will emulate a IDE interface. This is simpler, and needs no changes.
If you're a little more adventuous, you could integrate your drivers (and SP3!) with nlite from another windows system - since i don't know your motherboard, i'd suggest going with the chipset and hard drive sets from driverpacks.net. and sp3 from the network installation option from MS. I've linked the driverpacks instructions since its probably easier and better than any guide i could do
edited Jun 6 '12 at 12:11
answered Jun 6 '12 at 11:10
Journeyman Geek♦Journeyman Geek
113k44217371
113k44217371
add a comment |
add a comment |
- You can use something like Hiren Boot cd.
- Or let it boot from SUSE first, when it wants to partition your hard try to delete all partitions you made with linux and reset your system after applying.
It should help you.
is it true? But where can I find the application (Hiren Boot cd). Thank you for your suggestion
– Eka Anggraini
Jun 6 '12 at 9:32
1
How exactly will hirens help? Which tool in hirens? What do you actually think she needs to do?
– Journeyman Geek♦
Jun 6 '12 at 9:47
O I know little what it is Hiren Boot cd. I have been searching for information across multiple sites. In there (Hiren boot CD) No information is that there are many other tools to repair the partition or disk. but inside full of illegal software compilations, such as partition magic, windows 98, windows 3.1, Acronis, Paragon, and so on ... technicians and weapons: tools & hard drive partitions, recover data, NTFS, file manager, and so forth. But I do not know the meaning clearly.
– Eka Anggraini
Jun 6 '12 at 10:23
1
So bad to see that my answer is -2. As a computer professional I just gave a point. If you google it a little, you will find exactly what you want. But as I should explain more, when hiren booted, tryHard Drive tools, about 7 tools I think. Partition magic for example (in old Versions). Or Paragon partiotion manager. Even you van boot your system with linux LIVE CD or any live cd. Then remove partitions and you are done, just apply and reboot.
– Hamed JML
Jun 6 '12 at 10:25
At last, I should say the only thing you need to do is to remove your partitions(partition table), and let windows to partition it. You can do it in about 1000 ways.
– Hamed JML
Jun 6 '12 at 10:35
|
show 1 more comment
- You can use something like Hiren Boot cd.
- Or let it boot from SUSE first, when it wants to partition your hard try to delete all partitions you made with linux and reset your system after applying.
It should help you.
is it true? But where can I find the application (Hiren Boot cd). Thank you for your suggestion
– Eka Anggraini
Jun 6 '12 at 9:32
1
How exactly will hirens help? Which tool in hirens? What do you actually think she needs to do?
– Journeyman Geek♦
Jun 6 '12 at 9:47
O I know little what it is Hiren Boot cd. I have been searching for information across multiple sites. In there (Hiren boot CD) No information is that there are many other tools to repair the partition or disk. but inside full of illegal software compilations, such as partition magic, windows 98, windows 3.1, Acronis, Paragon, and so on ... technicians and weapons: tools & hard drive partitions, recover data, NTFS, file manager, and so forth. But I do not know the meaning clearly.
– Eka Anggraini
Jun 6 '12 at 10:23
1
So bad to see that my answer is -2. As a computer professional I just gave a point. If you google it a little, you will find exactly what you want. But as I should explain more, when hiren booted, tryHard Drive tools, about 7 tools I think. Partition magic for example (in old Versions). Or Paragon partiotion manager. Even you van boot your system with linux LIVE CD or any live cd. Then remove partitions and you are done, just apply and reboot.
– Hamed JML
Jun 6 '12 at 10:25
At last, I should say the only thing you need to do is to remove your partitions(partition table), and let windows to partition it. You can do it in about 1000 ways.
– Hamed JML
Jun 6 '12 at 10:35
|
show 1 more comment
- You can use something like Hiren Boot cd.
- Or let it boot from SUSE first, when it wants to partition your hard try to delete all partitions you made with linux and reset your system after applying.
It should help you.
- You can use something like Hiren Boot cd.
- Or let it boot from SUSE first, when it wants to partition your hard try to delete all partitions you made with linux and reset your system after applying.
It should help you.
answered Jun 6 '12 at 9:22
Hamed JMLHamed JML
3091414
3091414
is it true? But where can I find the application (Hiren Boot cd). Thank you for your suggestion
– Eka Anggraini
Jun 6 '12 at 9:32
1
How exactly will hirens help? Which tool in hirens? What do you actually think she needs to do?
– Journeyman Geek♦
Jun 6 '12 at 9:47
O I know little what it is Hiren Boot cd. I have been searching for information across multiple sites. In there (Hiren boot CD) No information is that there are many other tools to repair the partition or disk. but inside full of illegal software compilations, such as partition magic, windows 98, windows 3.1, Acronis, Paragon, and so on ... technicians and weapons: tools & hard drive partitions, recover data, NTFS, file manager, and so forth. But I do not know the meaning clearly.
– Eka Anggraini
Jun 6 '12 at 10:23
1
So bad to see that my answer is -2. As a computer professional I just gave a point. If you google it a little, you will find exactly what you want. But as I should explain more, when hiren booted, tryHard Drive tools, about 7 tools I think. Partition magic for example (in old Versions). Or Paragon partiotion manager. Even you van boot your system with linux LIVE CD or any live cd. Then remove partitions and you are done, just apply and reboot.
– Hamed JML
Jun 6 '12 at 10:25
At last, I should say the only thing you need to do is to remove your partitions(partition table), and let windows to partition it. You can do it in about 1000 ways.
– Hamed JML
Jun 6 '12 at 10:35
|
show 1 more comment
is it true? But where can I find the application (Hiren Boot cd). Thank you for your suggestion
– Eka Anggraini
Jun 6 '12 at 9:32
1
How exactly will hirens help? Which tool in hirens? What do you actually think she needs to do?
– Journeyman Geek♦
Jun 6 '12 at 9:47
O I know little what it is Hiren Boot cd. I have been searching for information across multiple sites. In there (Hiren boot CD) No information is that there are many other tools to repair the partition or disk. but inside full of illegal software compilations, such as partition magic, windows 98, windows 3.1, Acronis, Paragon, and so on ... technicians and weapons: tools & hard drive partitions, recover data, NTFS, file manager, and so forth. But I do not know the meaning clearly.
– Eka Anggraini
Jun 6 '12 at 10:23
1
So bad to see that my answer is -2. As a computer professional I just gave a point. If you google it a little, you will find exactly what you want. But as I should explain more, when hiren booted, tryHard Drive tools, about 7 tools I think. Partition magic for example (in old Versions). Or Paragon partiotion manager. Even you van boot your system with linux LIVE CD or any live cd. Then remove partitions and you are done, just apply and reboot.
– Hamed JML
Jun 6 '12 at 10:25
At last, I should say the only thing you need to do is to remove your partitions(partition table), and let windows to partition it. You can do it in about 1000 ways.
– Hamed JML
Jun 6 '12 at 10:35
is it true? But where can I find the application (Hiren Boot cd). Thank you for your suggestion
– Eka Anggraini
Jun 6 '12 at 9:32
is it true? But where can I find the application (Hiren Boot cd). Thank you for your suggestion
– Eka Anggraini
Jun 6 '12 at 9:32
1
1
How exactly will hirens help? Which tool in hirens? What do you actually think she needs to do?
– Journeyman Geek♦
Jun 6 '12 at 9:47
How exactly will hirens help? Which tool in hirens? What do you actually think she needs to do?
– Journeyman Geek♦
Jun 6 '12 at 9:47
O I know little what it is Hiren Boot cd. I have been searching for information across multiple sites. In there (Hiren boot CD) No information is that there are many other tools to repair the partition or disk. but inside full of illegal software compilations, such as partition magic, windows 98, windows 3.1, Acronis, Paragon, and so on ... technicians and weapons: tools & hard drive partitions, recover data, NTFS, file manager, and so forth. But I do not know the meaning clearly.
– Eka Anggraini
Jun 6 '12 at 10:23
O I know little what it is Hiren Boot cd. I have been searching for information across multiple sites. In there (Hiren boot CD) No information is that there are many other tools to repair the partition or disk. but inside full of illegal software compilations, such as partition magic, windows 98, windows 3.1, Acronis, Paragon, and so on ... technicians and weapons: tools & hard drive partitions, recover data, NTFS, file manager, and so forth. But I do not know the meaning clearly.
– Eka Anggraini
Jun 6 '12 at 10:23
1
1
So bad to see that my answer is -2. As a computer professional I just gave a point. If you google it a little, you will find exactly what you want. But as I should explain more, when hiren booted, tryHard Drive tools, about 7 tools I think. Partition magic for example (in old Versions). Or Paragon partiotion manager. Even you van boot your system with linux LIVE CD or any live cd. Then remove partitions and you are done, just apply and reboot.
– Hamed JML
Jun 6 '12 at 10:25
So bad to see that my answer is -2. As a computer professional I just gave a point. If you google it a little, you will find exactly what you want. But as I should explain more, when hiren booted, tryHard Drive tools, about 7 tools I think. Partition magic for example (in old Versions). Or Paragon partiotion manager. Even you van boot your system with linux LIVE CD or any live cd. Then remove partitions and you are done, just apply and reboot.
– Hamed JML
Jun 6 '12 at 10:25
At last, I should say the only thing you need to do is to remove your partitions(partition table), and let windows to partition it. You can do it in about 1000 ways.
– Hamed JML
Jun 6 '12 at 10:35
At last, I should say the only thing you need to do is to remove your partitions(partition table), and let windows to partition it. You can do it in about 1000 ways.
– Hamed JML
Jun 6 '12 at 10:35
|
show 1 more comment
Thanks for contributing an answer to Super User!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f433272%2fhard-drive-not-detected-after-installing-the-operating-system%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
1
Suse 10.0 is really old, and when i was using it, horribly buggy. In addition to that you really need to tell us more about your hard drive - sata or pata - and what version of windows you are trying to install (XP, vista or 7?)
– Journeyman Geek♦
Jun 6 '12 at 9:42
the night before I did install Windows XP SP2. Then the next morning, I tried to install linux and failed. Well that's where the problem began. what is kernel dump? I didn't know. Can you explain to me. Thank you
– Eka Anggraini
Jun 6 '12 at 10:08
kernel dump is BSOD on linux. I can try to help, but i need more details on hardware, like what sort of hard drive you have
– Journeyman Geek♦
Jun 6 '12 at 10:10
Thank you for your answer. I know now, Apparently my computer hard drive is not recognized by OS XP SP1, SP2 and SP3, due to be converted into serial SATA. But the windows 98 and windows vista can be installed. I'm confused until now, why could turn out that way. Was it because the failed installation of linux?
– Eka Anggraini
Jun 6 '12 at 10:56
If Windows Xp is not detecting the hard drive then you can try to install the Vista or 7. If they can detect the HDD then delete all the partitions and then recreate them through windows and then try to install XP again.
– avirk
Jun 6 '12 at 16:05