Does it matter what size of via you use in high frequency circuits?
Here is an image of an LNB and there is some different "Via"s in the PCB that I don't know Why do they use different size of Vias in such circuits. Why? Any reason?
I showed two Vias using two arrows that are close each other(Right side of the image).
pcb-design high-frequency
add a comment |
Here is an image of an LNB and there is some different "Via"s in the PCB that I don't know Why do they use different size of Vias in such circuits. Why? Any reason?
I showed two Vias using two arrows that are close each other(Right side of the image).
pcb-design high-frequency
1
larger vias have wider aspect ratio, thus lower inductance
– analogsystemsrf
Nov 27 at 12:17
1
@analogsystemsrf Okay, But why two different vias on a PCB?
– Roh
Nov 27 at 12:20
Relevant because same board and OP: electronics.stackexchange.com/questions/409083/…
– pipe
Nov 27 at 15:08
add a comment |
Here is an image of an LNB and there is some different "Via"s in the PCB that I don't know Why do they use different size of Vias in such circuits. Why? Any reason?
I showed two Vias using two arrows that are close each other(Right side of the image).
pcb-design high-frequency
Here is an image of an LNB and there is some different "Via"s in the PCB that I don't know Why do they use different size of Vias in such circuits. Why? Any reason?
I showed two Vias using two arrows that are close each other(Right side of the image).
pcb-design high-frequency
pcb-design high-frequency
asked Nov 27 at 12:13
Roh
2,80052766
2,80052766
1
larger vias have wider aspect ratio, thus lower inductance
– analogsystemsrf
Nov 27 at 12:17
1
@analogsystemsrf Okay, But why two different vias on a PCB?
– Roh
Nov 27 at 12:20
Relevant because same board and OP: electronics.stackexchange.com/questions/409083/…
– pipe
Nov 27 at 15:08
add a comment |
1
larger vias have wider aspect ratio, thus lower inductance
– analogsystemsrf
Nov 27 at 12:17
1
@analogsystemsrf Okay, But why two different vias on a PCB?
– Roh
Nov 27 at 12:20
Relevant because same board and OP: electronics.stackexchange.com/questions/409083/…
– pipe
Nov 27 at 15:08
1
1
larger vias have wider aspect ratio, thus lower inductance
– analogsystemsrf
Nov 27 at 12:17
larger vias have wider aspect ratio, thus lower inductance
– analogsystemsrf
Nov 27 at 12:17
1
1
@analogsystemsrf Okay, But why two different vias on a PCB?
– Roh
Nov 27 at 12:20
@analogsystemsrf Okay, But why two different vias on a PCB?
– Roh
Nov 27 at 12:20
Relevant because same board and OP: electronics.stackexchange.com/questions/409083/…
– pipe
Nov 27 at 15:08
Relevant because same board and OP: electronics.stackexchange.com/questions/409083/…
– pipe
Nov 27 at 15:08
add a comment |
1 Answer
1
active
oldest
votes
Vias have inductance and the more spindly they are, the larger the inductance. Note that in the equation above, inductance is proportional to the height of the via multiplied by the formula in the square brackets. That square bracket formula result is smaller when dimension $d$ is larger hence, inductance drops with larger diameter vias.
Picture from this website.
You also can't rule out parallel resonance with its parasitic capacitance either. The inductance and capacitance of the via form a parallel tuned circuit and, that could block a high frequency component of a signal in some cases. Using two different via sizes side-by-side might be the way the designer had in mind of "spoiling" the resonances.
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f409090%2fdoes-it-matter-what-size-of-via-you-use-in-high-frequency-circuits%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
Vias have inductance and the more spindly they are, the larger the inductance. Note that in the equation above, inductance is proportional to the height of the via multiplied by the formula in the square brackets. That square bracket formula result is smaller when dimension $d$ is larger hence, inductance drops with larger diameter vias.
Picture from this website.
You also can't rule out parallel resonance with its parasitic capacitance either. The inductance and capacitance of the via form a parallel tuned circuit and, that could block a high frequency component of a signal in some cases. Using two different via sizes side-by-side might be the way the designer had in mind of "spoiling" the resonances.
add a comment |
Vias have inductance and the more spindly they are, the larger the inductance. Note that in the equation above, inductance is proportional to the height of the via multiplied by the formula in the square brackets. That square bracket formula result is smaller when dimension $d$ is larger hence, inductance drops with larger diameter vias.
Picture from this website.
You also can't rule out parallel resonance with its parasitic capacitance either. The inductance and capacitance of the via form a parallel tuned circuit and, that could block a high frequency component of a signal in some cases. Using two different via sizes side-by-side might be the way the designer had in mind of "spoiling" the resonances.
add a comment |
Vias have inductance and the more spindly they are, the larger the inductance. Note that in the equation above, inductance is proportional to the height of the via multiplied by the formula in the square brackets. That square bracket formula result is smaller when dimension $d$ is larger hence, inductance drops with larger diameter vias.
Picture from this website.
You also can't rule out parallel resonance with its parasitic capacitance either. The inductance and capacitance of the via form a parallel tuned circuit and, that could block a high frequency component of a signal in some cases. Using two different via sizes side-by-side might be the way the designer had in mind of "spoiling" the resonances.
Vias have inductance and the more spindly they are, the larger the inductance. Note that in the equation above, inductance is proportional to the height of the via multiplied by the formula in the square brackets. That square bracket formula result is smaller when dimension $d$ is larger hence, inductance drops with larger diameter vias.
Picture from this website.
You also can't rule out parallel resonance with its parasitic capacitance either. The inductance and capacitance of the via form a parallel tuned circuit and, that could block a high frequency component of a signal in some cases. Using two different via sizes side-by-side might be the way the designer had in mind of "spoiling" the resonances.
edited Nov 27 at 12:28
answered Nov 27 at 12:23
Andy aka
239k10176407
239k10176407
add a comment |
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f409090%2fdoes-it-matter-what-size-of-via-you-use-in-high-frequency-circuits%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
1
larger vias have wider aspect ratio, thus lower inductance
– analogsystemsrf
Nov 27 at 12:17
1
@analogsystemsrf Okay, But why two different vias on a PCB?
– Roh
Nov 27 at 12:20
Relevant because same board and OP: electronics.stackexchange.com/questions/409083/…
– pipe
Nov 27 at 15:08