Add 2 HDD connected via USB to Synology DS211j using Raid 1
up vote
0
down vote
favorite
I have a Synology DS211j and 2 old 2TB S-ATA HDD. What I plan to do is to buy two cases for these two hard disk drives that allow for connecting the hard disks to my Synology using the USB port. I then want to build a Raid 1 with the two hard disks. I studied the manual and tried to google, but I can't figure out if that's possible at all, and if, how I can achieve that. Any hint?
hard-drive usb raid nas synology
add a comment |
up vote
0
down vote
favorite
I have a Synology DS211j and 2 old 2TB S-ATA HDD. What I plan to do is to buy two cases for these two hard disk drives that allow for connecting the hard disks to my Synology using the USB port. I then want to build a Raid 1 with the two hard disks. I studied the manual and tried to google, but I can't figure out if that's possible at all, and if, how I can achieve that. Any hint?
hard-drive usb raid nas synology
Just checking, but are you aware that this is going to be slow? Multiple drives on a single USB2 controller is going to give you about 30MB/sec for one drive and about twice 15MB/sec if you use two drives. With RAID 1 that means 30MB/sec read and 15MB/sec write (since the data is written to both drives). To give you a rough idea, that means 37 hours to fill the 2TB disk with data.
– Hennes
Oct 29 '14 at 13:49
Yes that should be ok. 100 GB should be written in two hours. I plan to use it to backup data that is written/accessed only rarely.
– RoflcoptrException
Oct 29 '14 at 13:51
Apparently you can enable ssh. Then you can log in and get busybox as a shell. Can you check if you can do that and if mdadm is installed by default (or if you can add it)?
– Hennes
Oct 29 '14 at 13:56
add a comment |
up vote
0
down vote
favorite
up vote
0
down vote
favorite
I have a Synology DS211j and 2 old 2TB S-ATA HDD. What I plan to do is to buy two cases for these two hard disk drives that allow for connecting the hard disks to my Synology using the USB port. I then want to build a Raid 1 with the two hard disks. I studied the manual and tried to google, but I can't figure out if that's possible at all, and if, how I can achieve that. Any hint?
hard-drive usb raid nas synology
I have a Synology DS211j and 2 old 2TB S-ATA HDD. What I plan to do is to buy two cases for these two hard disk drives that allow for connecting the hard disks to my Synology using the USB port. I then want to build a Raid 1 with the two hard disks. I studied the manual and tried to google, but I can't figure out if that's possible at all, and if, how I can achieve that. Any hint?
hard-drive usb raid nas synology
hard-drive usb raid nas synology
asked Oct 29 '14 at 13:44
RoflcoptrException
60671733
60671733
Just checking, but are you aware that this is going to be slow? Multiple drives on a single USB2 controller is going to give you about 30MB/sec for one drive and about twice 15MB/sec if you use two drives. With RAID 1 that means 30MB/sec read and 15MB/sec write (since the data is written to both drives). To give you a rough idea, that means 37 hours to fill the 2TB disk with data.
– Hennes
Oct 29 '14 at 13:49
Yes that should be ok. 100 GB should be written in two hours. I plan to use it to backup data that is written/accessed only rarely.
– RoflcoptrException
Oct 29 '14 at 13:51
Apparently you can enable ssh. Then you can log in and get busybox as a shell. Can you check if you can do that and if mdadm is installed by default (or if you can add it)?
– Hennes
Oct 29 '14 at 13:56
add a comment |
Just checking, but are you aware that this is going to be slow? Multiple drives on a single USB2 controller is going to give you about 30MB/sec for one drive and about twice 15MB/sec if you use two drives. With RAID 1 that means 30MB/sec read and 15MB/sec write (since the data is written to both drives). To give you a rough idea, that means 37 hours to fill the 2TB disk with data.
– Hennes
Oct 29 '14 at 13:49
Yes that should be ok. 100 GB should be written in two hours. I plan to use it to backup data that is written/accessed only rarely.
– RoflcoptrException
Oct 29 '14 at 13:51
Apparently you can enable ssh. Then you can log in and get busybox as a shell. Can you check if you can do that and if mdadm is installed by default (or if you can add it)?
– Hennes
Oct 29 '14 at 13:56
Just checking, but are you aware that this is going to be slow? Multiple drives on a single USB2 controller is going to give you about 30MB/sec for one drive and about twice 15MB/sec if you use two drives. With RAID 1 that means 30MB/sec read and 15MB/sec write (since the data is written to both drives). To give you a rough idea, that means 37 hours to fill the 2TB disk with data.
– Hennes
Oct 29 '14 at 13:49
Just checking, but are you aware that this is going to be slow? Multiple drives on a single USB2 controller is going to give you about 30MB/sec for one drive and about twice 15MB/sec if you use two drives. With RAID 1 that means 30MB/sec read and 15MB/sec write (since the data is written to both drives). To give you a rough idea, that means 37 hours to fill the 2TB disk with data.
– Hennes
Oct 29 '14 at 13:49
Yes that should be ok. 100 GB should be written in two hours. I plan to use it to backup data that is written/accessed only rarely.
– RoflcoptrException
Oct 29 '14 at 13:51
Yes that should be ok. 100 GB should be written in two hours. I plan to use it to backup data that is written/accessed only rarely.
– RoflcoptrException
Oct 29 '14 at 13:51
Apparently you can enable ssh. Then you can log in and get busybox as a shell. Can you check if you can do that and if mdadm is installed by default (or if you can add it)?
– Hennes
Oct 29 '14 at 13:56
Apparently you can enable ssh. Then you can log in and get busybox as a shell. Can you check if you can do that and if mdadm is installed by default (or if you can add it)?
– Hennes
Oct 29 '14 at 13:56
add a comment |
1 Answer
1
active
oldest
votes
up vote
1
down vote
Nope can't be done as yet. The drives would have to be internal. The DSM software doesn't allow any of these configurations via USB as these are shown as external devices and no options around RAID are shown:
USB options screen
I assume as someone said above because of poor performance and USB controllers being slower.
If there isn't any space to put these into the SATA controllers internally then maybe buy a bigger box? Synology offer all sorts of hardware configs and a 4 drive bay that I have works wonders.
You can even get a small 2 drive bay second hand on ebay to do what you need.
I guess this is for a backup situation? You can then link the 2 synology boxes to sync across and use as a backup.
Or if going for a bigger Synology box create separate RAID configs, although best practice DR you would have something offsite too just in case.
Anyhow let me know if you need more help.
Why was this voted down? I wish downvoters would add comments to say so. Especially when it isn't obvious.
– HankCa
Mar 29 '17 at 23:20
Not sure either why it was, always looking to improve so if someone could help understand why voted down.
– TheNerdyNerd
Apr 6 '17 at 9:10
add a comment |
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
up vote
1
down vote
Nope can't be done as yet. The drives would have to be internal. The DSM software doesn't allow any of these configurations via USB as these are shown as external devices and no options around RAID are shown:
USB options screen
I assume as someone said above because of poor performance and USB controllers being slower.
If there isn't any space to put these into the SATA controllers internally then maybe buy a bigger box? Synology offer all sorts of hardware configs and a 4 drive bay that I have works wonders.
You can even get a small 2 drive bay second hand on ebay to do what you need.
I guess this is for a backup situation? You can then link the 2 synology boxes to sync across and use as a backup.
Or if going for a bigger Synology box create separate RAID configs, although best practice DR you would have something offsite too just in case.
Anyhow let me know if you need more help.
Why was this voted down? I wish downvoters would add comments to say so. Especially when it isn't obvious.
– HankCa
Mar 29 '17 at 23:20
Not sure either why it was, always looking to improve so if someone could help understand why voted down.
– TheNerdyNerd
Apr 6 '17 at 9:10
add a comment |
up vote
1
down vote
Nope can't be done as yet. The drives would have to be internal. The DSM software doesn't allow any of these configurations via USB as these are shown as external devices and no options around RAID are shown:
USB options screen
I assume as someone said above because of poor performance and USB controllers being slower.
If there isn't any space to put these into the SATA controllers internally then maybe buy a bigger box? Synology offer all sorts of hardware configs and a 4 drive bay that I have works wonders.
You can even get a small 2 drive bay second hand on ebay to do what you need.
I guess this is for a backup situation? You can then link the 2 synology boxes to sync across and use as a backup.
Or if going for a bigger Synology box create separate RAID configs, although best practice DR you would have something offsite too just in case.
Anyhow let me know if you need more help.
Why was this voted down? I wish downvoters would add comments to say so. Especially when it isn't obvious.
– HankCa
Mar 29 '17 at 23:20
Not sure either why it was, always looking to improve so if someone could help understand why voted down.
– TheNerdyNerd
Apr 6 '17 at 9:10
add a comment |
up vote
1
down vote
up vote
1
down vote
Nope can't be done as yet. The drives would have to be internal. The DSM software doesn't allow any of these configurations via USB as these are shown as external devices and no options around RAID are shown:
USB options screen
I assume as someone said above because of poor performance and USB controllers being slower.
If there isn't any space to put these into the SATA controllers internally then maybe buy a bigger box? Synology offer all sorts of hardware configs and a 4 drive bay that I have works wonders.
You can even get a small 2 drive bay second hand on ebay to do what you need.
I guess this is for a backup situation? You can then link the 2 synology boxes to sync across and use as a backup.
Or if going for a bigger Synology box create separate RAID configs, although best practice DR you would have something offsite too just in case.
Anyhow let me know if you need more help.
Nope can't be done as yet. The drives would have to be internal. The DSM software doesn't allow any of these configurations via USB as these are shown as external devices and no options around RAID are shown:
USB options screen
I assume as someone said above because of poor performance and USB controllers being slower.
If there isn't any space to put these into the SATA controllers internally then maybe buy a bigger box? Synology offer all sorts of hardware configs and a 4 drive bay that I have works wonders.
You can even get a small 2 drive bay second hand on ebay to do what you need.
I guess this is for a backup situation? You can then link the 2 synology boxes to sync across and use as a backup.
Or if going for a bigger Synology box create separate RAID configs, although best practice DR you would have something offsite too just in case.
Anyhow let me know if you need more help.
edited Nov 10 '16 at 13:31
answered Nov 10 '16 at 11:06
TheNerdyNerd
34825
34825
Why was this voted down? I wish downvoters would add comments to say so. Especially when it isn't obvious.
– HankCa
Mar 29 '17 at 23:20
Not sure either why it was, always looking to improve so if someone could help understand why voted down.
– TheNerdyNerd
Apr 6 '17 at 9:10
add a comment |
Why was this voted down? I wish downvoters would add comments to say so. Especially when it isn't obvious.
– HankCa
Mar 29 '17 at 23:20
Not sure either why it was, always looking to improve so if someone could help understand why voted down.
– TheNerdyNerd
Apr 6 '17 at 9:10
Why was this voted down? I wish downvoters would add comments to say so. Especially when it isn't obvious.
– HankCa
Mar 29 '17 at 23:20
Why was this voted down? I wish downvoters would add comments to say so. Especially when it isn't obvious.
– HankCa
Mar 29 '17 at 23:20
Not sure either why it was, always looking to improve so if someone could help understand why voted down.
– TheNerdyNerd
Apr 6 '17 at 9:10
Not sure either why it was, always looking to improve so if someone could help understand why voted down.
– TheNerdyNerd
Apr 6 '17 at 9:10
add a comment |
Thanks for contributing an answer to Super User!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f833268%2fadd-2-hdd-connected-via-usb-to-synology-ds211j-using-raid-1%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Just checking, but are you aware that this is going to be slow? Multiple drives on a single USB2 controller is going to give you about 30MB/sec for one drive and about twice 15MB/sec if you use two drives. With RAID 1 that means 30MB/sec read and 15MB/sec write (since the data is written to both drives). To give you a rough idea, that means 37 hours to fill the 2TB disk with data.
– Hennes
Oct 29 '14 at 13:49
Yes that should be ok. 100 GB should be written in two hours. I plan to use it to backup data that is written/accessed only rarely.
– RoflcoptrException
Oct 29 '14 at 13:51
Apparently you can enable ssh. Then you can log in and get busybox as a shell. Can you check if you can do that and if mdadm is installed by default (or if you can add it)?
– Hennes
Oct 29 '14 at 13:56